Fordmods Logo

tickford_6 MK1 escort build thread...now with pics 

 

Page 1 of 1 [ 14 posts ] 

 
 Post subject: tickford_6 MK1 escort build thread...now with pics
Posted: Thu Mar 27, 2008 10:19 pm 
Getting Side Ways
Offline

Posts: 6449

Joined: 11th Nov 2004

Image
Image
Image
Image
Image
Image
Image
Image
Image

finaly a 4cyl section, although it may take time to become a fast moving thing.


anyway one to the point of this thread.

I needed some where to post the progress of the build and the other forums are full of the same stuff, so i figure here is a good place.

It all started when i was GIVEN a pair MK1 escorts. one as a none rolling shell, the other as a roller with a few extras like glass some lights and few other bits.
I also scored a MK1 panel van with a 4spd box and 1600 pushrod engine.
Over time I've rounded up a few other bits like a semi complete MK2 2 door, a 2L zetec engine from a 1998 mondeo, and a number of 1600 engine and 2L engine and parts.

the plan is to build a road registered car to run in the local hill climb and spint races.

So far work has revolved around stripping the needed parts from the donor cars, and getting the shed ready to take the shell that the build will be based on.


here are the pics
this is what my place looked like about 3 months ago.
the brown car is gone after donating anything that wasn't rusted. including boot lid, bonnet, heater 'bubble' from engine bay, glass and few small item.
the green panel van is 3/4 stripped now, though to clear up some space i might do a front cut on it and store the front end in my container.
the red MK2 will give up it's front end and it's diff

Image
Image
Image
Image

Last edited by tickford_6 on Thu Dec 17, 2009 7:16 pm, edited 3 times in total.

Top
 Profile  
 
 
 Post subject: Re: The official tickford_6 MK1 escort build thread...
Posted: Fri Mar 28, 2008 12:47 am 
Getting Side Ways
Offline
User avatar

Age: 35

Posts: 3505

Joined: 1st May 2005

Ride: EB Fairmont

Location: Northern Suburbs, Adelaide
SA, Australia

tickford_6 wrote:
finaly a 4cyl section, although it may take time to become a fast moving thing.


anyway one to the point of this thread.

I needed some where to post the progress of the build and the other forums are full of the same stuff, so i figure here is a good place.

It all started when i was GIVEN a pair MK1 escorts. one as a none rolling shell, the other as a roller with a few extras like glass some lights and few other bits.
I also scored a MK1 panel van with a 4spd box and 1600 pushrod engine.
Over time I've rounded up a few other bits like a semi complete MK2 2 door, a 2L zetec engine from a 1998 mondeo, and a number of 1600 engine and 2L engine and parts.

the plan is to build a road registered car to run in the local hill climb and spint races.

So far work has revolved around stripping the needed parts from the donor cars, and getting the shed ready to take the shell that the build will be based on.


was going to add some pics, seems at this moment i can't


What are you going to do with the mondeo engine mod wise?

 

_________________

Doin it for Scotty.

Top
 Profile  
 
 
Posted: Fri Mar 28, 2008 8:23 pm 
Getting Side Ways
Offline

Posts: 6449

Joined: 11th Nov 2004

mild cam upgrade and some side drought carbs. I'll have to make the extractors and run a programable igntion, looking at a megajolt, as it will run the mondeo coils and use the mondeo crank sensor.

should be good for about 180hp. at less then a third the cost of builing a 180hp pinto.
Top
 Profile  
 
 
Posted: Sun Mar 30, 2008 2:48 pm 
Getting Side Ways
Offline
User avatar

Age: 47

Posts: 1669

Joined: 23rd Dec 2004

Gallery: 1 images

Ride: Boosted ED XR6, EBII Mont Wgn

Power: 252 rwkw

Location: Mildura
VIC, Australia

I my self have a longterm project, Ecsort MKII 2 door rally pack my plans are complete overhaul and mondeo 2L EFI engine, I have quite a while to do it as it will be for my son, now 3.. i'll be keeping a close eye on your build good luck with it all :) ..

 

_________________

Image
[SEXYR-6] ED XR6 T5 Turbo Build
[EBW-347] EB Wagon V8 Stroker Build
FordMods Member #1761

Top
 Profile  
 
 
Posted: Tue Apr 01, 2008 11:10 pm 
Getting Side Ways
Offline

Posts: 6449

Joined: 11th Nov 2004

talk about a slow moving forum. lol


progress has been set back by another week. a good friend of ours came home from a work trip to find half the sump oil from her magna on the driveway. so this weekend i'll be sorting that out for her and doing nothing on the escorts at all. at this rate it'll never be done
Top
 Profile  
 
 
Posted: Wed Apr 16, 2008 8:47 pm 
Getting Side Ways
Offline
User avatar

Age: 52

Posts: 3531

Joined: 5th Nov 2004

Gallery: 25 images

Ride: 93 Maverick LWB/S2 LWB Delica

Power: 75 rwkw

Location: uoʇǝlƃuıs lʍoq ʇsnp
NSW, Australia

What is the panel van body like, other than the standard heater box rust and maybe floor due to that rust.

I would love to own another Esky panel van for a run around, cheap to own and much fun.

 

_________________

93 Ford Maverick LWB automatic petrol guzzler (gets stuck where Deli doesn't, big pumpkins :evil:)
97 S2 Mitsubishi Delica LWB (off the road getting v8 transplant)

Top
 Profile  
 
 
Posted: Wed Apr 16, 2008 11:22 pm 
Getting Side Ways
Offline

Posts: 6449

Joined: 11th Nov 2004

Macca wrote:
What is the panel van body like, other than the standard heater box rust and maybe floor due to that rust.

I would love to own another Esky panel van for a run around, cheap to own and much fun.



the body is basicly a bucket of s**t!! lol
body filler in both rear 1/4s and both barn doors. heater box is isn't rusted but will be removed,
floor is ok and both doors are coming off. wont be much left after i'm done
Top
 Profile  
 
 
 Post subject: Re: tickford_6 MK1 escort build thread...now with pics
Posted: Fri Apr 17, 2009 1:37 pm 
Getting Side Ways
Offline
User avatar

Age: 35

Posts: 2517

Joined: 27th Mar 2006

Gallery: 1 images

Ride: FG MkII Xr6t Ute

Location: Brisbane
QLD, Australia

Digging deep, but any progress ticky?

edit: also I am guessing this is to run in improved production class?

 

_________________

EVL098 wrote:
Cramping in the hand from having it on your Wang for an excessive period of time is a definate con.
Seriously do people google "f**k up modifications for Fords owned by Jews" and get linked straight to this site nowadays?

AU,factory fitted tickford kit/IRS, t5,Sports ryder/KYB: gone.

Last edited by skidder on Sat Oct 03, 2009 5:05 pm, edited 1 time in total.

Top
 Profile  
 
 
 Post subject: Re: tickford_6 MK1 escort build thread...now with pics
Posted: Sat Apr 18, 2009 9:50 pm 
Getting Side Ways
Offline

Posts: 6449

Joined: 11th Nov 2004

not really. :cry: :cry: :cry:

the van has been front cutted. so i can dump the rear section after removing all the turret steel. (to make rust repair sections)

but with the baby, the house (kitchen) and the patrol. there has been little time or money to spend.
my last spare $2000 went into the patrol.

when i get the escort on the build rig, which i need to do as there is alot of low cost prepwork i can do while money is a little tight.
i'll post all the picks and info.

i'll also be in hospital soon to have my gall bladder taken out. I've spent most of the past week in stupid amounts of pain.
Top
 Profile  
 
 
 Post subject: Re: tickford_6 MK1 escort build thread...now with pics
Posted: Mon Apr 27, 2009 5:59 pm 
Getting Side Ways
Offline

Age: 33

Posts: 1092

Joined: 14th Mar 2006

Ride: 2009 FG XR6 turbo project

Location: perth
WA, Australia

go the escorts \m/

ive built a mkII van.
and i have a mkII ghia
and i had a mkI 4 door.

i did have all 3 at once but after my big brother rolled his car i gave up the mkI for free as he was broke and couldnt afford a car.

Attachment:
mk2 ghia.jpg


Attachment:
Party bus.jpg


i dont have any pics of the mkI on my computer, i'll try to find some.

some of you may remember seeing it.

i also have a MINT TF cortina. really low kays. picked it up for $500. but due to complications it had to be unlisenced. so now im stripping the rear brakes and the 2L and dropping in a 302 windsor and turning it into a burnout car. ill post up pics of it later on.

i still own the van and the ghia.

its a shame the mkI van is too far gone. theyre pretty rare.

keep the updates coming. with pics :lol:

You do not have the required permissions to view the files attached to this post.
Top
 Profile  
 
 
 Post subject: Re: tickford_6 MK1 escort build thread...now with pics
Posted: Thu Aug 13, 2009 7:06 am 
Fordmods Newbie
Offline

Age: 33

Posts: 1

Joined: 13th Aug 2009

Ride: 1975 mk1 escort coupe

Location: tamworth
NSW, Australia

hey mate how is ur project going i m looking at puting a zetec in my mk1 2 door that i m restoring..

can you give me an eyedear on whats involved

thanks nathan
Top
 Profile  
 
 
 Post subject: Re: tickford_6 MK1 escort build thread...now with pics
Posted: Mon Aug 17, 2009 10:00 pm 
Getting Side Ways
Offline

Posts: 6449

Joined: 11th Nov 2004

escort8 wrote:
hey mate how is ur project going i m looking at puting a zetec in my mk1 2 door that i m restoring..

can you give me an eyedear on whats involved

thanks nathan



It's at a stand still at them moment. kids, wedding, 4WD. doesn't leave alot of time or money for it.

the zetec will bolt to the pinto or 1600 gearbox, the 1300 used a light duty box that will not stand up to even a stock zetec.

You will need to make/buy
engine mounts, Get the one that weld to the chassis rails.

extractors, these can be bought from the UK but may be cheaper to have custom made

a water rail for the thermostat, the original is bolted to the back of the head and will hit the firewall,
You can buy these from retroford and maybe Burton power in the UK.(best to by these not make them)

conversion flywheel, If you donor car is a manual you can mix and match the Zetec pressure plate with a pinto friction plate. Otherwise just buy a flywheel that will take a complete pinto clutch.

Carbs or injection? Burton do a manifold to use DCOE webers or EFI throttle bodies with the weber flange.
the stock plastic intake manifold wont fit an escort, you can get fabricated plenum intake from the uk

there are two types of water pump. one of them spins the wrong way for use in an escort. make sure you use the right one.

the rod bolts are weak. and shouldn't be reved over 6800rpm. you cna fit ARP bolt with out striping the engine. you just need to remove the sump. with good bolts the rods are good for 7500rpm.

The sump will need modding to fit, but i suggest buying the retroford one

i think i've covered it all.
Top
 Profile  
 
 
 Post subject: Re: tickford_6 MK1 escort build thread...now with pics
Posted: Sat Feb 13, 2010 8:52 pm 
Oompa Loompa
Offline

Age: 40

Posts: 46

Joined: 18th Jan 2009

Ride: ed

Location: central west nsw
NSW, Australia

any progress on the esky?
Top
 Profile  
 
 
 Post subject: Re: tickford_6 MK1 escort build thread...now with pics
Posted: Wed Mar 03, 2010 9:59 pm 
Getting Side Ways
Offline

Posts: 6449

Joined: 11th Nov 2004

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 14 posts ] 

Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Mar 29, 2024 6:29 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names