|
| EF_wanabe |
|
||
|
hey all ,
Used to own a EF with an AU motor in it now ive got a set of AU s2/3 spark plugs left over since the EF crashed can i use then AU plugs into my EA? the Bosch book shows different part numbers i dunno why though |
||
| Top | |
||
| TROYMAN |
|
||
|
yea they will fit.. if they are au2 or 3 listed plugs the difference is in the gap..
ea-au1 plugs have a 1.1mm gap, au2 and 3 have a 1.3 gap.. otherwise they will fit and work fine just re gap them to 1.1 |
||
| Top | |
||
| EF_wanabe |
|
||
|
Nice thought so great to know its just a gap
|
||
| Top | |
||
| cjh |
|
|||
|
The reach of the electrode is completely different...XF, EA plugs are very long.
this is an EA plug....NGK BRE527Y-11 http://i16.ebayimg.com/05/i/000/88/30/5cef_2.JPG this is an EF,EL,AU plug....NGK BPR5EY-11 http://shop.advanceautoparts.com/wcssto ... i_larg.jpg
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| EF_wanabe |
|
||
|
cjh wrote: The reach of the electrode is completely different...XF, EA plugs are very long. this is an EA plug....NGK BRE527Y-11 http://i16.ebayimg.com/05/i/000/88/30/5cef_2.JPG this is an EF,EL,AU plug....NGK BPR5EY-11 http://shop.advanceautoparts.com/wcssto ... i_larg.jpg Hmm strange i can see what you mean on ebay motor craft spark plugs are suited for EA-AU though |
||
| Top | |
||
| TROYMAN |
|
||
|
EF_wanabe wrote: cjh wrote: The reach of the electrode is completely different...XF, EA plugs are very long. this is an EA plug....NGK BRE527Y-11 http://i16.ebayimg.com/05/i/000/88/30/5cef_2.JPG this is an EF,EL,AU plug....NGK BPR5EY-11 http://shop.advanceautoparts.com/wcssto ... i_larg.jpg Hmm strange i can see what you mean on ebay motor craft spark plugs are suited for EA-AU though it dont matter, either way they will still work, i got ngk bp6ey in my au. |
||
| Top | |
||
| cjh |
|
|||
|
I'm only pointing it out due to the difference in the combustion chambers of the heads....EA's having a Swirl Ridge, and the EF/EL not having one.
Remember it was an Engineer that spec'd those plugs....and on a dyno, you would see a difference.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| efxr6wagon |
|
||
|
The projected tip of the EA plug is basically the "secret" behind the JMM plugs. The story goes that they were sent the wrong plugs by accident, but they made an extra 3-4 kw (tested on an EF). These projected-tip "wrong" plugs are the Autolite 985s that JMM sell for more than twice the price of anywhere else. I can't confirm the accuracy of their power gain claims, but I have been using them for years in my EF and AU2 with no problems (even with the thinner MLS head gasket and .015" shaved head in the EF). It looks like the NGK BRE527Y is very similar, though not sure about the heat range.
_________________ 95 EF XR6 wagon, 17" FTRs, DBA rotors, KYB/Koni, AU bottom end, ported EF head, backcut valves, SS Inductions, Territory intake, 10.2 CR, Auckland 1258 cam, vernier gear, PH4480 headers, no cat, Tickford 2.5", 2800rpm stall, J3 chip |
||
| Top | |
||
| EF_wanabe |
|
||
|
Should be all the same its only a falcon after all but im going to other way around AU plugs into EA but ehh whatever fits
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 66 guests |
