Fordmods Logo

EL BBM Conversion 

 

Page 1 of 1 [ 4 posts ] 

 
 Post subject: EL BBM Conversion
Posted: Sat Apr 11, 2009 2:41 pm 
Parts Gopher
Offline

Age: 26

Posts: 67

Joined: 29th Jun 2008

Ride: EB Fairmont

Location: Wollongong
NSW, Australia

Does any1 have a wiring diagram for putting a EL/AU BBM on my AU motor in my EB S1 which was running a log manifold. And also a list of parts that are needed to do the conversion, and any other info i might need for the conversion. And is there any difference between the EL and AU BBMs? Cheers

 

_________________

Silver EB Fairmont- AU S3 engine, Tickford Head, EF handbrake, T5 manual, EF XR6 3.45 LSD, 2.5" Catback by Rapid Exhaust, EL BBM, EL XR6 ECU, EL Thermos, EB Ghia interior, Kingy Superlows, Monroe struts
Now with a Walbro 255lph fuel pump :grin:

soon to come a crankin sound system boo yeh!!!!

Top
 Profile  
 
 
 Post subject: Re: EL BBM Conversion
Posted: Sat Apr 11, 2009 2:48 pm 
Smokin em up
Offline
User avatar

Posts: 262

Joined: 5th Nov 2006

Location: wilcannia
NSW, Australia

look in the faqs up the page a bit. and in the ecu section. this'll probably answermost of your questions.

 

_________________

vote for pedro ? f**k pedro, f**k him up his stupid a***hole.

Top
 Profile  
 
 
 Post subject: Re: EL BBM Conversion
Posted: Sat Apr 11, 2009 9:05 pm 
Getting Side Ways
Offline

Posts: 5582

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

MY.93.ED wrote:
Does any1 have a wiring diagram for putting a EL/AU BBM on my AU motor in my EB S1 which was running a log manifold.


It is quite simple. You need the plug off an EL TPS. Solder it to the loom off the log manifold where the original TPS was. You will also need to extend the wires due to the different position of the throttle body. The best way is to lay the log loom on the BBM and identifiy where all the sensors and plugs are on the BBM, then extend/change the log loom where necessary.

MY.93.ED wrote:
And also a list of parts that are needed to do the conversion, and any other info i might need for the conversion.


The BBM with throttle body.
EL metal heater hose from lower thermostat housing.
EL metal heater hose from rear of water pump that goes under exhaust manifold and around the back of the engine.
EL heater/water hoses.
The fuel lines are different and depending on how much of them you get with the manifold will determine how you go about attaching them.
EL airbox, intake and piping.
EL throttle cable and pedal.


MY.93.ED wrote:
And is there any difference between the EL and AU BBMs? Cheers


Yes there is. You need the EL BBM as the AU has different fittings specific to the AU that are not compatable with the E series.

Hope that helps

BenJ

 

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top
 Profile  
 
 
 Post subject: Re: EL BBM Conversion
Posted: Sun Apr 12, 2009 12:22 am 
Parts Gopher
Offline

Age: 26

Posts: 67

Joined: 29th Jun 2008

Ride: EB Fairmont

Location: Wollongong
NSW, Australia

cheers benj that helps alot.

 

_________________

Silver EB Fairmont- AU S3 engine, Tickford Head, EF handbrake, T5 manual, EF XR6 3.45 LSD, 2.5" Catback by Rapid Exhaust, EL BBM, EL XR6 ECU, EL Thermos, EB Ghia interior, Kingy Superlows, Monroe struts
Now with a Walbro 255lph fuel pump :grin:

soon to come a crankin sound system boo yeh!!!!

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 4 posts ] 

Who is online

Users browsing this forum: No registered users and 23 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Mon Dec 18, 2017 10:34 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names