|
| erick |
|
||
|
hi i have just done a manual conversion on my eb and put a J3 chip in that has converted my auto to a manual xr6 gas and is revving pritty high anyone have any info i have an EL computer and an AU motor and the chip came from T.I performance cheers.. mikey
_________________ Ford EB gli, AU conversion , 2 1/5 zorst, port and polish head, 5 speed, 17 inch rims, TI chip, lowered, gas powered. (sons car) |
||
| Top | |
||
| nalane |
|
|||
|
reset the base timing and idle then go from there. Don't forget its a new chip that has not been tuned to a car.
|
|||
| Top | |
|||
| erick |
|
||
|
its been pre programmed
_________________ Ford EB gli, AU conversion , 2 1/5 zorst, port and polish head, 5 speed, 17 inch rims, TI chip, lowered, gas powered. (sons car) |
||
| Top | |
||
| nalane |
|
|||
|
yes it has been reprogramed but it has not been tuned to your engine.
|
|||
| Top | |
|||
| galapogos01 |
|
|||
Posts: 1139 Joined: 27th Feb 2005 Ride: Supercharged EF Fairmont Location: T.I. Performance HQ |
It was inadvertently programmed with an Auto tune - which will cause high base idle in a Manual (due to missing trans temp sensor amongst other things).
Will be reprogramming it and sending it back out, should work out OK. It's a standard AU engine after all! Cheers, Jason
_________________ T.I. Performance - Ford Performance Tuning - J3 Chips & Tuning, Fuel Pumps & Injectors, Camshafts and much more! |
|||
| Top | |
|||
| nalane |
|
|||
|
just gone up a step in my estimation. somebody that will actually admit a mistake and be prepared to fix it.
|
|||
| Top | |
|||
| erick |
|
||
|
yes they are it was a mistake and should be ready to go next week
_________________ Ford EB gli, AU conversion , 2 1/5 zorst, port and polish head, 5 speed, 17 inch rims, TI chip, lowered, gas powered. (sons car) |
||
| Top | |
||
| 87SIlude |
|
||
|
Where can I get a chip for my eb?
Sorry to hyjack. |
||
| Top | |
||
| galapogos01 |
|
|||
Posts: 1139 Joined: 27th Feb 2005 Ride: Supercharged EF Fairmont Location: T.I. Performance HQ |
www.tiperformance.com.au !
_________________ T.I. Performance - Ford Performance Tuning - J3 Chips & Tuning, Fuel Pumps & Injectors, Camshafts and much more! |
|||
| Top | |
|||
| 87SIlude |
|
||
|
so basically the cost of a dyno run plus $190.
whats a dyno normally cost. |
||
| Top | |
||
| kickn_it |
|
||
|
Well a basic Dyno run is usually about $40-60. As T.I.performance want your AFR and RPM on the dyno sheet it may cost a bit more but shop around.
Im not to sure about places in NSW but VIC i can get a basic 3 pass run for about $50. Good luck.
_________________
|
||
| Top | |
||
| 87SIlude |
|
||
|
Cheers man.
|
||
| Top | |
||
| galapogos01 |
|
|||
Posts: 1139 Joined: 27th Feb 2005 Ride: Supercharged EF Fairmont Location: T.I. Performance HQ |
I'll just add that you don't have to supply a dyno sheet, though it does allow a more accurate tune. There are also non-custom tune chips i.e. XR6, Manual bins etc.
Cheers, Jason
_________________ T.I. Performance - Ford Performance Tuning - J3 Chips & Tuning, Fuel Pumps & Injectors, Camshafts and much more! |
|||
| Top | |
|||
| Campbell18 |
|
|||
|
i also heard that its recommended that an EL ECU is installed in EA-ED Falcons?? will a J3 still work with the earlier model ECU's?
_________________ ED 4.0L auto... pacemaker PH4480, Aus Pac Catback exhaust, wade 1636 with j3 tune =130rwkw |
|||
| Top | |
|||
| galapogos01 |
|
|||
Posts: 1139 Joined: 27th Feb 2005 Ride: Supercharged EF Fairmont Location: T.I. Performance HQ |
Hi Campbell,
Yes it will work with the earlier ECUs, but EL ecus are cheap, a good upgrade, and recommended for the reasons stated in http://www.tiperformance.com.au/Technic ... 0EA-ED.pdf . Cheers, Jason
_________________ T.I. Performance - Ford Performance Tuning - J3 Chips & Tuning, Fuel Pumps & Injectors, Camshafts and much more! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 58 guests |
