|
| jamie22_cole |
|
|||
|
hey guys do new lifters usually take time to go quiet or should they be quiet as soon as u turn the motor over cause just finish putting my AU/EL motor into my EL with all new gaskets, timing kit and new lifters (nason brand) they are bloody noisey some have quieten down but still not what I would like it to be. I have install these correctly and i have good oil pressure. so if anyone can give me any relief it would be very helpful thanks.
|
|||
| Top | |
|||
| SWC |
|
||
|
How long has the car been running?
What brand lifters did you use? They can take a little while to pump up and settle down. |
||
| Top | |
||
| jamie22_cole |
|
|||||
|
just like 15mins ago I turn it over hoping it went all well which did except the noisey lifters. i had the car running for about ten mins I would say got a pic of the oil pressure.
|
|||||
| Top | |
|||||
| Mad2 |
|
|||
|
did you soak them in oil before fitting them?
|
|||
| Top | |
|||
| jamie22_cole |
|
|||
|
sure did but the engine sat there for about a week and a half cause I went to queensland for christmas
|
|||
| Top | |
|||
| ranga83 |
|
||
|
i'd say let them bleed up abit. ive had some go quiet straight away and some took half a day driving.
_________________ ef futura, pacemakers, 2.5inch catback, k&n panel filter and 3.45 lsd. extractors/cat, ticky head, custom cam grind, t5. now onto cosmetics. |
||
| Top | |
||
| SWC |
|
||
|
Mad2 wrote: did you soak them in oil before fitting them? You don't soak them in oil before fitting. They need to be bled down before fitment. |
||
| Top | |
||
| SWC |
|
||
|
jamie22_cole wrote: just like 15mins ago I turn it over hoping it went all well which did except the noisey lifters. i had the car running for about ten mins I would say got a pic of the oil pressure. Take it for a run and see how it goes, they can take a while to pump up but driving around will speed up the process. |
||
| Top | |
||
| TimmyA |
|
|||
|
I had new Nason lifters in my ED and they didn't go silent even after a week... I ended up pulling them back out and sending them back under warranty... Replaced with a second set and they too were noisy (at least 2 of them)... I then bought Nason retainers and rebuilt the genuine ones and fitted them back in and they worked sweet...
As such I don't go much on brand new Nason lifters... The retainers but work ok... Cheers, Tim
_________________ 93 Red ED 5spd Manual Build Thread |
|||
| Top | |
|||
| jamie22_cole |
|
|||
|
ill take it out tonight after dinner and see how it go then. it the first set of lifters ive replace so I was unsure what the result would be.
|
|||
| Top | |
|||
| cjh |
|
|||
|
I fitted Nason HLA's into my ED, and they were noisy on start up ( as expected ), I held the rpm up at 2,000 rpm to 3,000 rpm, and constantly vary it between those two for about 5 minutes or so...no noise after that.....that was the Ford way of dealing with it.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| jamie22_cole |
|
|||
|
awesome just took the car out for a drive and the lifters were noisy for about 5mins on the highway and then when I went to turn around to head back home the lifter noises were gone.
|
|||
| Top | |
|||
| Mad2 |
|
|||
|
SWC wrote: Mad2 wrote: did you soak them in oil before fitting them? You don't soak them in oil before fitting. They need to be bled down before fitment. best remember that aye! 
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 73 guests |
