Fordmods Logo

Re: ef futura will not start. 

 

Page 1 of 1 [ 4 posts ] 

 
 Post subject: Re: ef futura will not start.
Posted: Sat May 17, 2014 2:14 pm 
Fordmods Newbie
Offline

Age: 34

Posts: 4

Joined: 16th Dec 2013

Gallery: 5 images

Ride: 1996 ef futura

Location: Brisbane
QLD, Australia

Still not working.put new bcm.replaced faulty ignetion .smart lock flashes rapidly..wants too start but wont..
Top
 Profile  
 
 
 Post subject: Re: ef futura will not start.
Posted: Sat May 17, 2014 5:19 pm 
Tyre Shredder
Offline

Age: 47

Posts: 346

Joined: 16th Jul 2007

Ride: EL Falcon

Power: 146 rwkw

Location: sydney
NSW, Australia

Keep ignition on for an hour. Make sure battery is fully charge before trying this.

 

_________________

FORD EL 4.0L. Crow cam, T.I Performance J3 Chip, Vernier cam gear, CMS stage 3 head, 68mm TB, AU head gasket + ARP studs, AU injectors, Pacey 4480, High flow cat, Shift kit, Stallie, 3:73 TrueTrac.

Top
 Profile  
 
 
 Post subject: Re: ef futura will not start.
Posted: Sat May 17, 2014 6:00 pm 
Technical Contributor
Offline

Age: 60

Posts: 6817

Joined: 22nd Jun 2005

Gallery: 8 images

Ride: EF Fairmont

Location: Campbelltown
NSW, Australia

kanebrizy wrote:
Still not working.put new bcm.replaced faulty ignetion .smart lock flashes rapidly..wants too start but wont..


Have you programed the BCM?
Top
 Profile  
 
 
 Post subject: Re: ef futura will not start.
Posted: Sat May 17, 2014 10:19 pm 
Technical Contributor
Offline

Posts: 492

Joined: 13th Jul 2013

Location: Campbelltown
NSW, Australia

As shown below, also confirm your interior light is operational first as this is power supply circuit...............................

SMARTLOCK SYSTEM MODULE REPLACEMENT & LEARN
PROCEDURES
SmartLock/BEM and CILA Learn Procedure
With vehicles EBII - ED and XG Ute the system has a stand-alone
SmartLock module. If you have replaced the CILA or the
SmartLock module in service, you will need to download the CILA
codes before you can start the car.
This procedure is the same for the EF Falcon based vehicle fitted
with a BEM module.
Procedure:
1. Turn off all accessories.
2. Ensure that the system is free from error. With the ignition
turned to the OFF position, the warning lamp will be flashing
the armed code.
3. Turn the ignition switch to the ON position. The warning lamp
should display error code 3, then flash the immobilised code.
Leave the ignition switch in the ON position.
4. After 30 minutes, the CILA codes will download to the
SmartLock module, the door locks will change state twice and
the warning lamp will go out.
5. Turn the ignition switch to the OFF position for at least 30
seconds, until the warning lamp displays the armed flash.
6. Verify the system by starting the engine.
Falcons based vehicles EL - AU and including XH Ute use the
same procedure with three exceptions:
1. The download time is 61 minutes.
2. AU Falcon based vehicle are not fitted with a warning lamp.
3. Once the codes are learnt and the door locks cycle the warning
lamp continues to flash until the ignition is turned OFF and ON
again.
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 4 posts ] 

Who is online

Users browsing this forum: No registered users and 21 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Thu Dec 14, 2017 1:34 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names