|
| relaxed_diplomacy |
|
||
|
Those rubbers you pulled out look blue, aftermarket plastic stuff, not original rubber.
Those nolathane arms look considerably weaker than the originals, unless they use a very thick wall, in which case they would be much heavier. I have two EB's and an EL all with over 225,000kms and all the original bushs in the lower control arms are working fine.
_________________ wrecking 9/97 EL fairmont sedan burgundy 6cyl auto 270k modBAintake |
||
| Top | |
||
| biggav |
|
|||
|
mine seems to vibrate quite heavy in first when taking it out in the revs then after second between say 2500 and 3500rpm its quite noticeable after that it smooths out im thinking tailshaft unbalance as i've replaced a worn uni only after 3mths of driving.
what do other people think?
_________________ 4.0lt Balanced Bottom End, ACL Race Internals, Rspec4 Cam, BPT Swichchip, PH4480, 2.5' Lukey, Scorcher Bodykit, T5 Manual frd906 wrote: LOLLOLLOLLOLOLLOLLOLLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOL
|
|||
| Top | |
|||
| dannyye |
|
|||
|
To relaxed_diplomacy,
I dunno with the blue bushes, they could have been replaced with existing owner i thought maybe they where the originals. As for the Nolethane control arms, they where pretty heavy and had very thick walls and IMO they looked alot sturdier than the ones that came off. To Mystro, Have you replaced your control arms and had success in fixing your problem? Not liking this new forum much...Miss the quick reply option
_________________ Ford Falcon BA XT 2003, Stock Engine, Factory Fitted LPG, Monroe GT Sports Shockers, King Coil Springs, Advanti Shine 19" 8x5 Rims, 2 1/2" Exhaust,DNA Fascia, Pioneer DEH-1350MPG Head Unit, Powervox 500watt 4 Channel Amp, Aerpro Hi/Lo Audio level converter, Pioneer 10" Sub Woofer |
|||
| Top | |
|||
| mystro |
|
||
|
dannyye wrote: To relaxed_diplomacy, I dunno with the blue bushes, they could have been replaced with existing owner i thought maybe they where the originals. As for the Nolethane control arms, they where pretty heavy and had very thick walls and IMO they looked alot sturdier than the ones that came off. To Mystro, Have you replaced your control arms and had success in fixing your problem? Not liking this new forum much...Miss the quick reply option i have it all ready to go in .its been to hot  ..i just replaced aklll the springs and shocks ,bump stops at pedders and thery didnt say there was any thing wrong with the bushes . i am replacing every bush ,mount,linkage ect with nolathane any way . i am gathering a heap of other parts to replace all at once. hopefully i can get up on a hoist by the end of this week and i will let yer know. cheers mystro : ) |
||
| Top | |
||
| SpeedyED |
|
|||
|
biggav wrote: mine seems to vibrate quite heavy in first when taking it out in the revs then after second between say 2500 and 3500rpm its quite noticeable after that it smooths out im thinking tailshaft unbalance as i've replaced a worn uni only after 3mths of driving. what do other people think? Biggav, does the vibration get more noticable when you gather speed??? Also, make sure your tailshaft bolts are tight (I've had a problem when the tailshaft bolts had come loose, the vibration was only in and out though).
_________________ Pre AU Adapters for sale |
|||
| Top | |
|||
| biggav |
|
|||
|
SpeedyED wrote: biggav wrote: mine seems to vibrate quite heavy in first when taking it out in the revs then after second between say 2500 and 3500rpm its quite noticeable after that it smooths out im thinking tailshaft unbalance as i've replaced a worn uni only after 3mths of driving. what do other people think? Biggav, does the vibration get more noticable when you gather speed??? Also, make sure your tailshaft bolts are tight (I've had a problem when the tailshaft bolts had come loose, the vibration was only in and out though). shaft bolts should/would be tight as just replaced the unis front and rear(rear was flogged to s**t) after 3500 in second(thats the main time it really shudders) it smooths out and gets up and going.
_________________ 4.0lt Balanced Bottom End, ACL Race Internals, Rspec4 Cam, BPT Swichchip, PH4480, 2.5' Lukey, Scorcher Bodykit, T5 Manual frd906 wrote: LOLLOLLOLLOLOLLOLLOLLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOL
|
|||
| Top | |
|||
| SpeedyED |
|
|||
|
I don't think it's the tailshaft, it could be something within the gearbox??? or maybe loose/worn Engine Mounts???
_________________ Pre AU Adapters for sale |
|||
| Top | |
|||
| biggav |
|
|||
|
ok thanks input shaft you think?
sure i got that replaced couple years ago when built the box for my other EA
_________________ 4.0lt Balanced Bottom End, ACL Race Internals, Rspec4 Cam, BPT Swichchip, PH4480, 2.5' Lukey, Scorcher Bodykit, T5 Manual frd906 wrote: LOLLOLLOLLOLOLLOLLOLLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOL
|
|||
| Top | |
|||
| SpeedyED |
|
|||
|
I'm really not the best person to ask when it comes to gearbox's, I find the best thing with this kind of thing is to do stuff like, make sure the engine mounts are in good nic and they are tight, same goes for the gearbox mounts, I don't think it's anything to do with suspension rubbers.
Really I think it's something internal in the Gearbox, but you never know, it could be something that's just a simple fix.
_________________ Pre AU Adapters for sale |
|||
| Top | |
|||
| ford383f |
|
|||
|
hey guys i got a bad vibration about 2000 to 2500 it rattles the change in the ashtray before jumping to the tail shaft it dose it in park and netual and sometimes on the road aswell as most ea's it has it's valve noise in the top end but cant think whats causing the bad shudder
worn big end maybe? cheers
_________________ 95' XG |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 82 guests |
