|
| opto |
|
|||
|
Iv'e just tested a new profile from Wade Cams called 1636, and I am extremely pleased with it.
If you are looking for something a little more meatier than the 1604 profile this is the cam for you. I put it in Tuesday 26/07/05 an couldn't wait to try it out, it has more lift than 1604 and I am running it with an auto with extractors and 2.5 inch zorst and 985 plugs and no valve spring issues like bounce or pinging. The thing is, not only do you have power, but way more torque to get you off the line, the power starts real low I recon 1200/1800 RPM right thru to 5000+ RPM, It pulls hard and gets you up to speed fast. Once it is at 80 or 100 k's the engine feels like it is ticking over but as soon as accelerate, it goes hard. You can run a standard ECU and I just upped the RPM 50 to 100. Yeh I know I have only had it in for 1 day but it is gruntier than the 1604 profile. I ran it in Economy mode and it didn't hold back. Keith from Wade has said its okay to tell you that they are now available for both auto's and manual's. Dont forget to mention Fordmods for your discount.
_________________ I post here cos the russian tank driver doesn't |
|||
| Top | |
|||
| Bug |
|
|||
|
Argh that be right.. Just when i put the 1604 in :\
_________________ EL XR6 5spd |
|||
| Top | |
|||
| sickd |
|
|||
|
i wonder how close it is to yobbos new cam would be interesting to find out
you and yobbo should compare cam figures to see if they are similar and if they are i would look to getting one as i cant get to bloody sydney  i think it was from sydney?
_________________ BA XR8 BOSS 260
|
|||
| Top | |
|||
| nathen |
|
||
|
im going to watch this thread becouse i will be after a cam swap very very soon
|
||
| Top | |
||
| stockstandard |
|
|||
|
got any cam specs?
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| Grechie |
|
||
|
how much is this cam?
_________________ Ford Falcon EA Naturally Aspirated 4.0L i6 |
||
| Top | |
||
| Gaz |
|
||
|
my guess, if hes put it in production... the same as all the other cams
refer to the sponsors section
_________________ 2007 Steel BF Ghia MKII V8 - 19" GTP's + Superlows |
||
| Top | |
||
| sickd |
|
|||
|
i guess this has not taken off yet come on guys with the cams we need you to get together and compare you dont have to post the specs unless you want to lol
_________________ BA XR8 BOSS 260
|
|||
| Top | |
|||
| Grechie |
|
||
|
i have a question, how do u go about getting it, do u send in ur current cam to wade and they send u back the 1636? btw im going to get this cam:)
_________________ Ford Falcon EA Naturally Aspirated 4.0L i6 |
||
| Top | |
||
| stockstandard |
|
|||
|
for regrind - yep. Send them your cam, they grind it to the new profile and send it back. Then you add some shims to the rocker arms to make up for the metal they took off and then your car goes faster...
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| twr7cx |
|
|||
|
Dang, just fitted the 1604 a month or so ago.
|
|||
| Top | |
|||
| opto |
|
|||
|
The inlet and exhaust opening and closing angles are nearly the same as the 1604 profile, the big difference if the valve lift is nearly .490 range.
If you want to send a cam to Wade, go to bunnings and get some stormwater pipe around 90 mm and some inspection cap with screw on ends. Glue the ends on with pipe glue, it not that expensive. Nowe wrap your cam up in an old towel or clean newspaper and put some paper on the end inside the pipe and put the cam in and put some paper in this end and screw the cap on and tape up both ends with say packing tape. On your computer print out wades address and you details, It should weigh around 7 kilos, postage from Adelaide to Victoria was 15 dollars. Arrange for Chris to phone you and pay for the cam and postage, I prefer registered. I think the cam was around $140.00, see Wades forum for the prices on the 1604 profile, Its the same price. Dont forget you will need shims ( From Ford or the wreckers) and new Lash adjuster retainer clips ( Coventry or Repco).
_________________ I post here cos the russian tank driver doesn't |
|||
| Top | |
|||
| Grechie |
|
||
|
thanks opto
Is it possible to go into there shop with the cam, and they regrind it on the spot? or do u leave it with them and come back? i was thinking about posting it...wades in oakleigh which is in victoria right?
_________________ Ford Falcon EA Naturally Aspirated 4.0L i6 |
||
| Top | |
||
| opto |
|
|||
|
I recon you can take one to them, best way is to get one from the wreckers, a little bit of work, In Adelaide we have Upullit parts and a cam is about 40 bucks but pick a good one nice smoothe lobes and runners.
And you get to keep your original cam.
_________________ I post here cos the russian tank driver doesn't |
|||
| Top | |
|||
| Futura_XR |
|
|||
|
do u have to upgrade valve springs at all to run this cam??? and also what are the shims worth??
_________________ Past: 150rwkw 5spd EF Futura - 4499's, 2.5" exh, Intake, Filter, Wade 1636, Head and Valve Work, Raised Comp.
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 68 guests |
