|
| wadesta_1986 |
|
|||
|
Hey Guys!
Currently, my car is on King Ultra Lows. Anyway, every now and again, with the steering even slightly turned, if it goes over a bump, the tyres give the inside of the guards a hard time. Is there any way I can sorta do a self rolling? Would a rubber mallet and some gentle tapping do the trick or should I just get them rolled? Any hints and tips would be great guys! Cheers! |
|||
| Top | |
|||
| Interceptor |
|
||
|
just get them rolled, theres too big a chance of kinking the guards or cracking paint if you DIY
_________________ Banned |
||
| Top | |
||
| wadesta_1986 |
|
|||
|
Interceptor wrote: just get them rolled, theres too big a chance of kinking the guards or cracking paint if you DIY
Yea, that was the biggest fear! Might have to try and hunt someone that can roll guards down! |
|||
| Top | |
|||
| NAfairlane... |
|
|||
|
isnt it like 60 a side at a panel beaters? or wheel fitters ?
_________________ Mercedes 500SEC: -- GONE -- http://www.fordmods.com/the-garage-f53/my-83-mercedes-500sec-buildup-t69837.html |
|||
| Top | |
|||
| RustyEF |
|
||
|
i did mine myself with just a hammer, its not that hard just push againts the guard when hitting with the hammer, make sure to use a warm cloth.
no creases in mine worked out fine,
_________________ -------EL Fairmont Ghia with CUstome BA XR body kit------- |
||
| Top | |
||
| Shum's EL |
|
|||
|
yeah just talk to panel beaters or wheel joints... most of them have the equipment or can point you in the direction of someone who can
|
|||
| Top | |
|||
| twirqurky |
|
||
|
Could be cheaper to put superlows in?
Just an option. |
||
| Top | |
||
| provked |
|
||
|
i used a jack handle ane rolled it around the outside of the wheel slowly folding the lip up un the guard, worked a treat. may even be worth pulling the guards out a little if you have wide wheels
_________________ 05 BA futura wagon, dumped, 19s, limo tint ( now the wifes car! |
||
| Top | |
||
| wadesta_1986 |
|
|||
|
Super Lows! Nah!! I Love the look of a Low LOW car.
It has 18" x 8" rims wrapped in 235/40 rubber. The rims are CSA's so they have a real shallow offset. All I was gonna do was wrap one of my Body Dollys in rubber and then just use a nylon hammer to push the inside of the guard in. |
|||
| Top | |
|||
| uglybob |
|
|||
|
wade - talk to clampy - he knows somewhere which does 'em. i need to get mine done too, i have massive chunks missing from my front tyres lol
_________________ R.I.P. Scotty |
|||
| Top | |
|||
| wadesta_1986 |
|
|||
|
uglybob wrote: wade - talk to clampy - he knows somewhere which does 'em. i need to get mine done too, i have massive chunks missing from my front tyres lol
Ok, thanks Fraser. I think Kyron paid $110 or somthing to get his done! And yea, I have the whole tyre thing to! It sux! |
|||
| Top | |
|||
| MilleniumFalcon |
|
|||
|
uglybob wrote: wade - talk to clampy - he knows somewhere which does 'em. i need to get mine done too, i have massive chunks missing from my front tyres lol
Have you checked the inside of your tyre as well? The inside of mine was almost completely worn down to the wire, when I was having the same problem with mine being too low |
|||
| Top | |
|||
| wadesta_1986 |
|
|||
|
Nah, The insides are fine. Its just the outside wall is sliced up a little bit
|
|||
| Top | |
|||
| mrnasty |
|
|||
|
MilleniumFalcon wrote: uglybob wrote: wade - talk to clampy - he knows somewhere which does 'em. i need to get mine done too, i have massive chunks missing from my front tyres lol Have you checked the inside of your tyre as well? The inside of mine was almost completely worn down to the wire, when I was having the same problem with mine being too low the guards wouldnt cause that, having a bad wheel alignment will
_________________ Cougar Zero makes my pants fit nice. |
|||
| Top | |
|||
| veeate |
|
|||
|
Auto FX WA
Desmond Wong 0412 034 861 this guy does them....charges $120 i think....ive tried heaps of wheel fitters & panel beaters in WA but couldnt find any one......give him a call..... |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 22 guests |
