Fordmods Logo

Au1 remote programming? 

 

Page 1 of 1 [ 6 posts ] 

 
 Post subject: Au1 remote programming?
Posted: Sun May 15, 2005 2:08 pm 
Smokin em up
Offline
User avatar

Posts: 225

Joined: 5th Nov 2004

Gallery: 1 images

Ride: Falcon

Location: Mount Gambier
SA, Australia

How do program the remote key pad from Au1
Top
 Profile  
 
 
Posted: Sun May 15, 2005 6:49 pm 
Site Admin
Offline
User avatar

Age: 42

Posts: 514

Joined: 5th Nov 2004

Gallery: 5 images

Ride: V8 VE Calais V Spec

Power: 262 rwkw

Location: Sydney
NSW, Australia

Hope this all helps

For AUI (Smartlock Models - 2 Button Remotes)
Up to four Keypads can be programmed and used with the Smartlock Remote Central locking system.
If you have replaced the BEM, or new keypads are being added to the system, you will need to train the keypad codes to the module.

1. The ignition switch should be in the Off position, with all the doors shut and Unlocked.
2. Turn the ignition key to the ACCESSORY position and within 5 seconds, operates the rear demister switch exactly three times in quick succession. (IE. Press the switch so the Demister light turns on, then off, then back on again.)
3. After the 5 seconds is up, the door locks will change state, to indicate that the BEM has entered keypad learn mode.
NOTE : All existing keypads at this point, have been erased from memory !
4. Press either buttons on the keypad that is to be trained. The door locks will change state twice, to indicate that the keypad has been added to the BEM memory.
5. Follow step 4. for each keypad that is to be added to the BEM memory. A maximum of 4 keypads can be added to the BEM memory.NOTE : You must teach all remote keypads for the Smartlock module, before proceeding.
6. When you have thought all the remote keypads, turn the ignition to the Off position to leave the learn mode. The door locks will change state to indicate a return to normal mode.
7. Check the function of both buttons on each keypad, to ensure that the keypad has been trained.



For AUI - Late Series (Smartsheild Models, 4 Button Remotes)
Up to four Keypads can be programed and used with the Smartsheild Remote Central locking system.
If you have replaced the BEM, or new keypads are being added to the system, you will need to train the keypad codes to the module.

1. The ignition switch should be in the Off position, with all the doors shut and Unlocked.
2. Turn the ignition key to the ACCESSORY position and within 5 seconds, operates the rear demister switch exactly three times in quick succession. (IE. Press the switch so the Demister light turns on, then off, then back on again.)
3. After the 5 seconds is up, the door locks will change state, to indicate that the BEM has entered keypad learn mode.
NOTE : All existing keypads at this point, have been erased from memory !
4. Press either buttons on the keypad that is to be trained. The door locks will change state twice, to indicate that the keypad has been added to the BEM memory.
5. Follow step 4. for each keypad that is to be added to the BEM memory. A maximum of 4 keypads can be added to the BEM memory. NOTE : You must teach all remote keypads for the Smartsheild module, before proceeding.
6. When you have taught all the remote keypads, turn the ignition to the Off position to leave the learn mode. The door locks will change state to indicate a return to normal mode.
7. Check the function of all buttons on each keypad, to ensure that the keypad has been trained.

 

_________________

VE Calais V8, IQ, HSV instruments and brembos fitted.
IQ, IPC, BCM all hacked and programmed without TECH2 :)

Top
 Profile  
 
 
Posted: Sun May 15, 2005 8:44 pm 
Smokin em up
Offline
User avatar

Posts: 225

Joined: 5th Nov 2004

Gallery: 1 images

Ride: Falcon

Location: Mount Gambier
SA, Australia

ok, done all that everything work to plan but not able to control the doors by the keypads ive replaced the batteries also noticed no flashing led on the dash I've not long acquired this vehicle
Top
 Profile  
 
 
Posted: Tue May 17, 2005 8:15 pm 
Site Admin
Offline
User avatar

Age: 42

Posts: 514

Joined: 5th Nov 2004

Gallery: 5 images

Ride: V8 VE Calais V Spec

Power: 262 rwkw

Location: Sydney
NSW, Australia

No flashing LED ????? You mean the smartlock LED ????

Hrmmm... I dont know a lot about the AU models, but check the Central Lock Fuse...
Does the Central Locking work at all ????
Also does your interior Lamp work ? (On EF/EL, part of the Smartlock Power comes from the interior Lamp fuse... If this fuse is blown, then the Smartlock Lamp will not flash... Hence the question)....

 

_________________

VE Calais V8, IQ, HSV instruments and brembos fitted.
IQ, IPC, BCM all hacked and programmed without TECH2 :)

Top
 Profile  
 
 
Posted: Tue May 17, 2005 9:37 pm 
Smokin em up
Offline
User avatar

Posts: 225

Joined: 5th Nov 2004

Gallery: 1 images

Ride: Falcon

Location: Mount Gambier
SA, Australia

Yeh the central locking works fine by the key not the pad, the interior light works aswell looks like a visit to the local Ford dealer to rip me off blind :(
thanks for the help
Top
 Profile  
 
 
Posted: Tue May 17, 2005 10:43 pm 
Technical Contributor
Offline

Age: 31

Posts: 6047

Joined: 12th Nov 2004

Ride: Ford Ef Futura

Location: Perth
WA, Australia

Is it the same for the E series Matti?
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 6 posts ] 

Who is online

Users browsing this forum: No registered users and 13 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Sat Dec 16, 2017 2:44 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names