Fordmods Logo

Early e series interior 

 

Page 1 of 1 [ 3 posts ] 

 
 Post subject: Early e series interior
Posted: Sat Aug 07, 2010 1:38 pm 
Smokin em up
Offline

Age: 32

Posts: 276

Joined: 27th Jun 2007

Location: Melbourne
VIC, Australia

Hey guys i got an early E series (boxcar) on the way as a project car, i want to spruce up the interior a bit, but im an apprentice so funds are tight, is it possible to use LTD leather seats in it? thanks much

sorry for the s**t grammar as im on my phone
Top
 Profile  
 
 
 Post subject: Re: Early e series interior
Posted: Sat Aug 07, 2010 8:42 pm 
Getting Side Ways
Offline

Age: 33

Posts: 971

Joined: 18th Dec 2008

Ride: BA Futura

Location: Hobart
TAS, Australia

The fronts will fir just fine, the rears are a bit different because the LTD would have a longer wheelbase.

Apparently people have made them fit many times, usually without too much trouble.

I'm sure someone who has done this will be able to give more details.

 

_________________

Image
DCII LTD V8 - leather - low k's
1978 XC '1/2' 500 project 302C
BA Futura wagon
P38 Range Rover HSE

Top
 Profile  
 
 
 Post subject: Re: Early e series interior
Posted: Sat Aug 07, 2010 10:41 pm 
Oompa Loompa
Offline

Age: 47

Posts: 28

Joined: 26th Jun 2010

Ride: ford fairlane nl ghia

Location: woodcroft
NSW, Australia

yeah i did this 3 years ago to a ed fairmont before i went to the darkside
dont worry im back in a for now

i did everything you are doing ltd seats door trims dash full ltd interior
dash fits but depending on if your has climate control may be hard with all vac lines
getting right new heater box

There is 2 mounting brackets that need to be moved to bolt dash up.

Depending weather yours is a v8 or i6 i had the v8 and to run the nf nl ltd dash
you will need to change the engine wiring harnes to match the nf nl along side the ltd computer
being that (correct me if im wrong) something like 34 pins on eb ed v8 to 36 pin of ef el v8
so dash wiring needs to match computer along side engine wiring needs to match

You will need to weld the hand brake assembly to floor

front & rear seats arent direct switch
the front seats from memory 3 bolts line up one dosent could be wrong been awhile....
back seats go in beleive it or not but the ltd seat gets squashed as the door closes does close but squashes against the door trim i removed the c clips and trimed the foam down a inch or 2 and strected the leather further around to look stock

door trims match straight up except you will need to shorten and bend the handle rod that attaches to the lock mechanism so it a few inches shorter so opens the door


other than that all i can think of of the top of my head hope this helps

and some one can add more and correct me as been along time

I love the ea - ed look tuff as especially with later e series interior get the best of both worlds

GOOD LUCK WITH HER
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 3 posts ] 

Who is online

Users browsing this forum: No registered users and 12 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Apr 19, 2024 6:39 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names