|
| easpak91 |
|
|||
|
I need a few questions answered to get this AU console into my EA.
How do i get the air pipes that run under the AU console to fit? The AU air pipe has a larger mouth for the front vent compared to the EA which is smaller do i have to cut and shut the pipes? The AU pipes are longer do i have to shorten the AU pipes? How do i secure the AU console to the floor as none of the original screw holes on the AU console match up with the ones on the floor of my EA? If anyone can shed some light and tips on this mod it would be appreciated...... 
_________________ WHO EVER SAID "TWOS COMPANY THREES A CROWD" OBVIOUSLY NEVER HAD A THREESOME |
|||
| Top | |
|||
| biggav |
|
|||
|
i just drilled my screws thru the box to the metal support on the tunnel and trimmed back the air tubes till they meshed together.
_________________ 4.0lt Balanced Bottom End, ACL Race Internals, Rspec4 Cam, BPT Swichchip, PH4480, 2.5' Lukey, Scorcher Bodykit, T5 Manual frd906 wrote: LOLLOLLOLLOLOLLOLLOLLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOL
|
|||
| Top | |
|||
| easpak91 |
|
|||
|
Did you use the EA or the AU air tubes? And how did you secure the front(under dash) of the AU console??
_________________ WHO EVER SAID "TWOS COMPANY THREES A CROWD" OBVIOUSLY NEVER HAD A THREESOME |
|||
| Top | |
|||
| easpak91 |
|
|||
|
I thought this mod was an easy one.......... i think i might be wrong
_________________ WHO EVER SAID "TWOS COMPANY THREES A CROWD" OBVIOUSLY NEVER HAD A THREESOME |
|||
| Top | |
|||
| phutchy |
|
||
|
use the front half of the ea tube and the back half of the au tube push the front half into the back half ..trim it up and tape it
|
||
| Top | |
||
| biggav |
|
|||
|
i left the AU tube where it was and just trimed the bell mouth of the AU tube to fit in with the EA one up under the dash
the consol goes nowhere with the 2 screws holding the consol in by the bin tight fit FTW!
_________________ 4.0lt Balanced Bottom End, ACL Race Internals, Rspec4 Cam, BPT Swichchip, PH4480, 2.5' Lukey, Scorcher Bodykit, T5 Manual frd906 wrote: LOLLOLLOLLOLOLLOLLOLLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOL
|
|||
| Top | |
|||
| easpak91 |
|
|||
|
Thanks might give it a go on the weekend.......
_________________ WHO EVER SAID "TWOS COMPANY THREES A CROWD" OBVIOUSLY NEVER HAD A THREESOME |
|||
| Top | |
|||
| Froudey |
|
||
|
search my posts and i think i posted up measurements and alike they measure almost identically.. simple job.
_________________ R.I.P Tobias my son. |
||
| Top | |
||
| Froudey |
|
||
|
Froudey wrote: search my posts and i think i posted up measurements and alike they measure almost identically.. simple job. Froudey wrote: Measured
AU Console 98cm Length 31cm Width 18cm Height EA Console 97cm Length 28cm Width 15cm Height Looked at these things AU console sits flush on the carpet / floor and the EA console sits square and looks s**t  yeah more inmoraion when i get a AU console to play with.
_________________ R.I.P Tobias my son. |
||
| Top | |
||
| easpak91 |
|
|||
|
Thanks for that, the problem im having is getting the AU pipes for the rear vents to line up with the EA's vent that comes out of the heater box which is situated under the dash, the EA mouth is smaller and squarer compared to the AU mouth which is more rectangle shape and has a larger opening. I might just cut the two in half(pipes) and rejoin them (which i didnt want to do as my EA console is in top condition)
_________________ WHO EVER SAID "TWOS COMPANY THREES A CROWD" OBVIOUSLY NEVER HAD A THREESOME |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Facebook [Bot] and 25 guests |
