|
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
CHEF wrote: Powerfc do not come adr aproved, its programable so it will never be approved.
Is there room for a 1JZ in the bay? That would be my budget kw pick, but otherwise the SR would be the pick of the 4cyl motors, just for the huge range of new and used bolt ons available in the same way a motec is, yet there are many claims of it being legal |
||
| Top | |
||
| CHEF |
|
|||
|
Yeah true, some versions of motec can be code locked by the installer/dealer but I havnt heard about Apexi offering this service and the government giving it the ok... sounds like he said she said talk
|
|||
| Top | |
|||
| mrnasty |
|
|||
|
why not try a 265 hemi in there???
In the E49 Chargers they were capable of running 13.9 with a minor tune and decent tyres. Imagine what a worked one would do in a little capri!!
_________________ Cougar Zero makes my pants fit nice. |
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
mrnasty wrote: why not try a 265 hemi in there???
In the E49 Chargers they were capable of running 13.9 with a minor tune and decent tyres. Imagine what a worked one would do in a little capri!! BIG hemi engine......little capri engine bay. it's all well and good to say X engine can make Y power or this one make more than that for the same dollars. but at the end of the day it has to FIT IN THE ENGINE BAY. inline sixes are not going to fit in a stock capri engine bay. V6 yes V8 yes. 265hemi no. the best options in terms of what fits, are the CA16/18, SR20, cosworth YB, the entire BD serries A through T, short deck windsor V8 289/302, best out of all of those would have to be the cosworth YB, in stock form out performs the SR in every way you can imagine, and fits a hell of alot easier then a V8 |
||
| Top | |
||
| ebs_4l |
|
||
|
tickford_6 wrote: yes i'm sure.
it comes pre approved you have to prove emissions compliance with it fitted to your vehicle, which includes complete drive cycle testing, and it must be password locked. motec and autronic are two that i know of that do meet the criteria of being able to meet adr requirements
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| EBXR8380 |
|
|||
|
How about one of these ???
http://www.sssautomotive.com.au/images/ ... _large.jpg
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| thano |
|
||
|
i recon , go with a half cut s13,upgrade to a s15 later model ball bearing turbo ,
which is good for 400 fly wheel hp or hks 2530, gtr style front mount, 3 inch exhaust from turbo to cat then 3.5 cat back, run uni chp or apexi of stock computer and you should have the power your after with min lag your other option would have more flow better responce if set up right , but cost? |
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
but why be a sheep??
i mean turbo the pinto thats in there already. a few years back the fastest 4cyl in the country was 2L mk1 escort that ran low 9s with the pinto engine. the bottom end was nothing over the top. forged pistons on preped stock rods. ported head that was a copy from the book by David visard, start with an imported late model pinto that was factory injected and all you need to do is wire in wolf 3d or EMS stinger. the stock injected rods a little stronger then the carby rods. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 15 guests |
