Fordmods Logo

df ltd wiring 

 

Page 1 of 1 [ 9 posts ] 

 
 Post subject: df ltd wiring
Posted: Wed Oct 20, 2010 9:26 pm 
Smokin em up
Offline

Age: 48

Posts: 204

Joined: 8th Apr 2007

Location: Sth Australia
SA, Australia

does anyone know if the eb v8 and ef v8 engine loom is the same?rg for injectors
Top
 Profile  
 
 
 Post subject: Re: df ltd wiring
Posted: Thu Oct 21, 2010 1:55 pm 
EFI Guru
Offline

Age: 58

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Yes except for climate control stuff there is an extra temp sender in the heater pipes. Some EB's have a climate control of course.
Top
 Profile  
 
 
 Post subject: Re: df ltd wiring
Posted: Thu Oct 21, 2010 5:22 pm 
Smokin em up
Offline

Age: 48

Posts: 204

Joined: 8th Apr 2007

Location: Sth Australia
SA, Australia

ahh ok ty chaged engine loom nyway still getting s park tried dizzy and coild as well wierd
only did a motor and trans swap
Top
 Profile  
 
 
 Post subject: Re: df ltd wiring
Posted: Thu Oct 21, 2010 5:52 pm 
EFI Guru
Offline

Age: 58

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Sorry I just saw you were comparing EF and EB. EF-Up won't have a separate temp sender for the temp gauge because they use the EEC ECT sensor and get serial data via the EEC to the cluster....otherwise they are the same.
Top
 Profile  
 
 
 Post subject: Re: df ltd wiring
Posted: Thu Oct 21, 2010 9:52 pm 
Smokin em up
Offline

Age: 48

Posts: 204

Joined: 8th Apr 2007

Location: Sth Australia
SA, Australia

ahh ok. i did an engine swap.new motor wont get spark. it had a eb engine loom in it so i changed that to a ef 1. but still not getting spark. have changed dizzy and coil.
Top
 Profile  
 
 
 Post subject: Re: df ltd wiring
Posted: Fri Oct 22, 2010 11:04 am 
EFI Guru
Offline

Age: 58

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Check your grounds...you should have zero ohms from block to battery negative. Is the block ground strap attached?...often this is forgotten during swaps as is the HEGO ground on the back of the intake manifold although, that has no bearing on ignition power.
Top
 Profile  
 
 
 Post subject: Re: df ltd wiring
Posted: Fri Oct 22, 2010 12:21 pm 
Technical Contributor
Offline
User avatar

Age: 34

Posts: 3714

Joined: 27th Sep 2006

Gallery: 20 images

Ride: ED Falcon

Power: 133 rwkw

Location: Leeton
NSW, Australia

Do you have 12 Volts at the coil?

Assuming you've replaced dizzy and coil with new ones? As the TFI module is a pretty common failure point in the dizzy's...

No spark is 1 of three things... Internal PIP module, external TFI module or coil... So I'd be making sure you've got volts to both the coil + side and the power wire into the TFI, Also the other red wire on the TFI is the crank wire... This should have voltage when the key is held to start... If power isn't getting to these then it isn't going to work...

As mentioned, power also wont get there if you missing hooking up the earth strap to the block...

Cheers,
Tim

 

_________________

93 Red ED 5spd Manual Build Thread

Performance: Complete AUII VCT Wiring & Power Train, Pacey Headers, 2.5" Exhaust, Exedy Clutch, DBA Rotors
Visuals: FG XR Wheel, XR Front, 17's, BA 5 Spd Shifter, BA Ghia Window Switches, NL Cluster
Tunes: 8" Pioneer Sub, JBL Speakers, Clarion Double DIN Headunit

Top
 Profile  
 
 
 Post subject: Re: df ltd wiring
Posted: Fri Oct 22, 2010 7:50 pm 
Smokin em up
Offline

Age: 48

Posts: 204

Joined: 8th Apr 2007

Location: Sth Australia
SA, Australia

have put dizzy and coil from a car i just drove in it
1.0 ohm resistant between block or any engine earth to battery -
there is 1 volts at coil and dizzy
there is power when u crank as well at the other wire
have tries ecu dizzy and coil from a running car and sill no charge
also left it for 30 mins to restset smartlock stuff just incase
put another dizzy cap of a car that was running
put multi meter on coil and it drops to 11volts when cranking
tested injector as well and it pulses
so not sure now lol bloody cars
Top
 Profile  
 
 
 Post subject: Re: df ltd wiring
Posted: Tue Nov 09, 2010 2:46 pm 
Smokin em up
Offline

Age: 48

Posts: 204

Joined: 8th Apr 2007

Location: Sth Australia
SA, Australia

re did another earth does have 1 but cant do it to the head bolt like normal cause there after market boltset
it now has spark but still not firing lol .it will with fuel sprayed in the throttle body
check pump thats working injectors r pulsing so maybe a fuel reg?
gummy injectors or s**t plugs
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 9 posts ] 

Who is online

Users browsing this forum: No registered users and 16 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Sat Apr 27, 2024 1:59 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names