|
| bevo86 |
|
||
|
hey guys
im building a 347 to drop in my ef. i have got just bout everything sorted except the maf sensor would the stock one be good enough or will i have to go bigger. and what problems can accure from this. any help would be much appreciated |
||
| Top | |
||
| XR9UTE |
|
||
|
Depends entirely on the specs of your engine?
|
||
| Top | |
||
| bevo86 |
|
||
|
well im running 80mm tb trick flow plenum and manifold. port matched gt40 heads blue 24lb injectors adjustable fuel reg walbro 500hp pump big mouth cold air intake looking to get a cam that runs from bout 2200 to 6800. got the sct eliminator for it as well.. thanks for responding man
there is no replacement for displacement gt1300 escort genuine ef xr8 5 speed |
||
| Top | |
||
| XR9UTE |
|
||
|
Which intake? and only port matching on the heads?
|
||
| Top | |
||
| bevo86 |
|
||
|
not sure what trick flow manifold it is. its alot larger then the standard one might be a street heat one. and port matching the heads to the manifold. plenum and manifold are pretty well matched
there is no replacement for displacement gt1300 escort genuine ef xr8 5 speed |
||
| Top | |
||
| XR9UTE |
|
||
|
Ok, a street heat is only on par with an explorer.
Unless you have a TFS R-series manifold and the heads(you don't specify which ones they are?) are hogged out big time I wouldn't be using a cam that goes to 6800. |
||
| Top | |
||
| bevo86 |
|
||
|
they are ported gt40 heads. I got the manifold set up second hand all it has on it is tfs-sbf.. ..
|
||
| Top | |
||
| XR9UTE |
|
||
|
Yes but which ones.... GT40 iron or GT40P iron or GT40Y alloy or GT40X alloy?
Got any photies of the intake? |
||
| Top | |
||
| bevo86 |
|
||
|
gt40p heads. Not at the moment will get sum. I no the ports are nearly 10mm longer then the satndard manifold that came with the heads
|
||
| Top | |
||
| bevo86 |
|
||
|
finally got back on here. the manifold i got with the heads is an explorer manifold the trick flow one i got from the states is heaps bigger in the ports compared to the explorer one. plus engine specs have changed now with the stroker kit and pistons im using the ci is now 353 and 2000rpm-6000rpm cam and just over 10.5-1 comp ratio. plus for futue refference waht sor of after market ecu would be good to put in it eg haltech
|
||
| Top | |
||
| XR9UTE |
|
||
|
Let me know the part # of the TFS intake?
What bore size gives you a 353? An 80mm Mercury Marauder MAF will do you for that combo...I mean with those heads. You don't need to go aftermarket for the ECU either. |
||
| Top | |
||
| bevo86 |
|
||
|
no worries man when i get down to the shop ill write it down.
well with the standard bore it was going to be a 347. wee have bored it out 40thou over im pretty sure and when we worked it out it scrapped in at the 353 mark. the stroker kit that we are using is a scat one with h beam rods and the pistons have a teflon coated skirt. sweet i was hoping i would have to go after market for the ecu fro what i have seen on the net perth boys are pullen decent hp using the sct chip plus a guy from a perfomance shop in newcastle said its a real pain in the a** to wire up an after market ecu in the e-serries your help has been much appreciated |
||
| Top | |
||
| bevo86 |
|
||
|
oh that was 40 thou over standard 302 windsor bore im using an au block. whicj is probs the wors one me and the boys have seen on one deck it was 12thou out
|
||
| Top | |
||
| XR9UTE |
|
||
|
No worries,
I suspected that you were going past .030" to get the 353ci figure which is concern for outright power. 5.0's are pretty thin in the cylinder walls and combined with a 3.4 stroke you'll have considerable side loads on the cylinder wall. Knowing that, it's probably a good thing that outright power will be limited by your heads and most likely the intake too. You're engine should survive ok in that case. You might also consider a Dart sportsman short block?...for the money they are at the moment it's pretty hard to pass up. Just been having a look and it seems the Marauder MAF is fairly difficult to come by now. You may have better luck finding a '96-up Cobra 80mm MAF or you can go aftermarket with a Pro-M 77-80mm job. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 17 guests |