Fordmods Logo

Home » Forums » Fordmods Tech » V8 Workshop

EL XR8 idle... 

 

Page 1 of 1 [ 10 posts ] 

Post New Topic Post Reply  Previous topic Next topic
 
XR8beast
 Post subject: EL XR8 idle...
Posted: Mon Oct 03, 2005 5:27 pm 
Fordmods Newbie
Offline

Age: 51

Posts: 19

Joined: 27th Mar 2005

Location: Sydney
NSW, Australia
Hi , I have a problem with my EL XR8 in hot weather, with the air con turned on it stalls when i pull up and then when i turn it back on it idles erratically up and down not over 1000 rpm though. In cold weather she runs beautiful any ideas ?. She has a new air filter , new plugs , clean MAF sensors and i run her on premium all the time.
Top
 Profile  
 
 
dodgie
Posted: Mon Oct 03, 2005 9:25 pm 
Stock as a Rock
Offline
User avatar

Age: 47

Posts: 117

Joined: 16th Apr 2005

Gallery: 9 images

Ride: ED Fairmont Ghia 5.0L

Location: Brisbane
QLD, Australia
Take off the idle speed controler on the side of the throttle body, and clean it out.
Make sure the valve inside moves freely, and stick it back on.

 

_________________

ED Fairmont Ghia.
306ci, Pro-m 80 MAF & #42inj, Kirban AFPR, Walbro 255LPH intank & inline, BBK 70mm, Ported Edelbrock #60399, Ported Explorer, Crane 2031 & YT1.72, MSD 6AL, paciemaker tri-y, 2.5" cats into single 3". H/D stall. 3.45 lsd, Powerdyne XB1A.
Top
 Profile  
 
 
XR8beast
Posted: Mon Oct 03, 2005 10:19 pm 
Fordmods Newbie
Offline

Age: 51

Posts: 19

Joined: 27th Mar 2005

Location: Sydney
NSW, Australia
Thanks dodgie , I'll give it a go tomorrow..
Top
 Profile  
 
 
SHE'S MY UTE
 Post subject: idel
Posted: Thu Oct 06, 2005 10:33 am 
Fordmods Newbie
Offline

Age: 34

Posts: 3

Joined: 6th Oct 2005

Location: Brisbane
QLD, Australia
my xr8 ute runs at a cool 1000rpm at idel and on take off(cause im driving) it gets to 3500rpm but my beast can fly

 

_________________

holdens go fast then fall apart but fords go fast and by pass the holdens
Top
 Profile  
 
 
dodgie
Posted: Thu Oct 06, 2005 1:19 pm 
Stock as a Rock
Offline
User avatar

Age: 47

Posts: 117

Joined: 16th Apr 2005

Gallery: 9 images

Ride: ED Fairmont Ghia 5.0L

Location: Brisbane
QLD, Australia
So what's your point?

 

_________________

ED Fairmont Ghia.
306ci, Pro-m 80 MAF & #42inj, Kirban AFPR, Walbro 255LPH intank & inline, BBK 70mm, Ported Edelbrock #60399, Ported Explorer, Crane 2031 & YT1.72, MSD 6AL, paciemaker tri-y, 2.5" cats into single 3". H/D stall. 3.45 lsd, Powerdyne XB1A.
Top
 Profile  
 
 
AUGhiaV8
Posted: Thu Oct 06, 2005 8:58 pm 
Parts Gopher
Offline

Posts: 82

Joined: 16th Apr 2005

Ride: AU Fairmont Ghia

Location: Brisbane
QLD, Australia
He's 15!

XR8beast... good advice from dodgie. Iit might pay you to disconnect the battery for an hour or so and do a full reset while you are at it. Make sure you go through the proper relearn procedure when you power up again.
Top
 Profile  
 
 
dodgie
Posted: Thu Oct 06, 2005 9:10 pm 
Stock as a Rock
Offline
User avatar

Age: 47

Posts: 117

Joined: 16th Apr 2005

Gallery: 9 images

Ride: ED Fairmont Ghia 5.0L

Location: Brisbane
QLD, Australia
Guess I would be an excitable little fella if I had a licence and owned an XR at 15years of age too.

 

_________________

ED Fairmont Ghia.
306ci, Pro-m 80 MAF & #42inj, Kirban AFPR, Walbro 255LPH intank & inline, BBK 70mm, Ported Edelbrock #60399, Ported Explorer, Crane 2031 & YT1.72, MSD 6AL, paciemaker tri-y, 2.5" cats into single 3". H/D stall. 3.45 lsd, Powerdyne XB1A.
Top
 Profile  
 
 
XR8beast
Posted: Thu Oct 06, 2005 10:18 pm 
Fordmods Newbie
Offline

Age: 51

Posts: 19

Joined: 27th Mar 2005

Location: Sydney
NSW, Australia
AUGhiaV8 wrote:
He's 15!

XR8beast... good advice from dodgie. Iit might pay you to disconnect the battery for an hour or so and do a full reset while you are at it. Make sure you go through the proper relearn procedure when you power up again.


Is that the procedure of driving it like it was stolen for a 100 k's or so :)
nah seriously what procedure do you mean exactly AUGhia ?
Top
 Profile  
 
 
dodgie
Posted: Thu Oct 06, 2005 10:38 pm 
Stock as a Rock
Offline
User avatar

Age: 47

Posts: 117

Joined: 16th Apr 2005

Gallery: 9 images

Ride: ED Fairmont Ghia 5.0L

Location: Brisbane
QLD, Australia
Here it is mate...
PCM Relearn Procedure
1. Run engine to normal operating temperature.
2. Allow engine to idle (Don't touch the throttle).
3. Run for 2 minutes in Drive with Air Conditioner ON.
4. Run for 2 minutes in Drive with Air Conditioner OFF.
5. Run for 2 minutes in Neutral with Air Conditioning ON.
6. Run for 2 minutes in Neutral with Air Conditioning OFF.
7. Road test for at least 5 minutes at various speeds.
(Ensure vehicle is operated in each gear position, including Reverse gear).

From the following link...
http://www.fordforums.com.au/showthread ... +procedure

Though the car will relearn all this over time, this procedure is quicker.

If this doesn't solve your problems, try checking the TPS voltages, but see how you go first.

 

_________________

ED Fairmont Ghia.
306ci, Pro-m 80 MAF & #42inj, Kirban AFPR, Walbro 255LPH intank & inline, BBK 70mm, Ported Edelbrock #60399, Ported Explorer, Crane 2031 & YT1.72, MSD 6AL, paciemaker tri-y, 2.5" cats into single 3". H/D stall. 3.45 lsd, Powerdyne XB1A.
Top
 Profile  
 
 
EBXR8380
Posted: Fri Oct 07, 2005 9:57 am 
Getting Side Ways
Offline
User avatar

Age: 70

Posts: 3555

Joined: 7th Nov 2004

Gallery: 4 images

Power: 482 rwkw

Location: Penrith
NSW, Australia
Check ignition system, maf, intake air temp sensor,coolant temp sensor....
Make sure idle is set correctly...Disc idle control , adjust idle, then reconnect idle motor...Then check TPS..It should be under 1v at idle and progressivly go up as throttle is opened to 5v...

 

_________________

As in ZOOM 126 edition
331 Dart block,3.25/ 4340 steel crank, Oliver rods,TFS ported track heat heads, TFS track heat inlet Twin SC61 turbo's
Project 1UZ-EF has started.. S475 Turbo 4.0 V8 Mustang Celica.....
Top
 Profile  
 
Display posts from previous:
Sort by  
Post New Topic Reply
 Page 1 of 1  [ 10 posts ] 
Jump to:  

Home » Forums » Fordmods Tech » V8 Workshop

Who is online

Users browsing this forum: No registered users and 14 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Sat Apr 27, 2024 3:54 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names