
|
| Falcon Powa |
|
|||
|
yeh i been reading dam!!! o well u think it be better then the stock el one? just for now i can buy one later.....
_________________ Phantom BA Xr6 turbo 4spd semi Auto... Stock
|
|||
| Top | |
|||
| huggiebear |
|
|||
|
im not sure what size the stock EL ones are. i went stright to the tickford one when i put my EL motor in
|
|||
| Top | |
|||
| Falcon Powa |
|
|||
|
ah ok well so if i head to ford dealer in town and ask for a Tickford snorkel for EL reckon they know wat im talkin bout? but ill install this one for now cause my other one is cracked a bit...
_________________ Phantom BA Xr6 turbo 4spd semi Auto... Stock
|
|||
| Top | |
|||
| huggiebear |
|
|||
|
try and find a EF/EL GT snorkel. i used to have one. they are huge
|
|||
| Top | |
|||
| Falcon Powa |
|
|||
|
ok sweet ill try find 1. also purchased a 3A racing filter. are they the same installation as the post before in this topic?
_________________ Phantom BA Xr6 turbo 4spd semi Auto... Stock
|
|||
| Top | |
|||
| lukey |
|
|||
|
They'd be same installation.
I thought EL GT snorkels are same size as AU XR8 snorkels? |
|||
| Top | |
|||
| Falcon Powa |
|
|||
|
been looking at my filter looks like i mite need some type of pipe or hose to connect the filter..... i got some pics i took today on my phone plus at nite with touch not that clear ill take some better ones tommorow at day since i got day off.......
You do not have the required permissions to view the files attached to this post.
_________________ Phantom BA Xr6 turbo 4spd semi Auto... Stock
|
|||
| Top | |
|||
| Falcon Powa |
|
|||
|
ok fellas just finish with my filter in my el falcon. hears wat ive done it was a quite of a hard job connecting the bottom of the pod with the top but ended all ok..... heres wat it looks like from the inside .............
any tips for wat i should do to improve this setup just mention them please cheers also was able to fit that BA snorkel in for now with one screw holding it on ill have to drill a hole later to fix this buts ok at the monment..... You do not have the required permissions to view the files attached to this post.
_________________ Phantom BA Xr6 turbo 4spd semi Auto... Stock
|
|||
| Top | |
|||
| udbdevo |
|
||
|
need sum help with mine...tryed to tackle it on the weekend and failed
i cut the hose and fitted the pod to see that the outside clip ( square thing) was not lined up with the ones on the box. after sussing it out further it seems that my pod is hitting the top of the airbox so their is no way it will fit properly. atm i have the pod sitting on the house with only a hose clamp and not screwed in. also the intake going to the throttle body had to be unbolted becuase the outside screws dont line up on the outside the throttle body intake pipe does not line up either. so pretty much it is all on 2gether except it is not 100% gap free and it is only being held on my hose clamps. i was thinking of fitting the pod over the pipe in the box and then cutting the airbox to fit over the top of the intake pipe(going intot he airbox),.,,if that makes sense so their would be a 5-10mm gap around the intake to the airbox... thoughts> |
||
| Top | |
||
| huggiebear |
|
|||
|
i think you need to take pics.. i cant visualise it
|
|||
| Top | |
|||
| EL__Fairmont |
|
|||
|
{USERNAME} wrote: need sum help with mine...tryed to tackle it on the weekend and failed
i cut the hose and fitted the pod to see that the outside clip ( square thing) was not lined up with the ones on the box. after sussing it out further it seems that my pod is hitting the top of the airbox so their is no way it will fit properly. atm i have the pod sitting on the house with only a hose clamp and not screwed in. also the intake going to the throttle body had to be unbolted becuase the outside screws dont line up on the outside the throttle body intake pipe does not line up either. so pretty much it is all on 2gether except it is not 100% gap free and it is only being held on my hose clamps. i was thinking of fitting the pod over the pipe in the box and then cutting the airbox to fit over the top of the intake pipe(going intot he airbox),.,,if that makes sense so their would be a 5-10mm gap around the intake to the airbox... thoughts> You could just buy a 3in 45degree storm water bend from Bunnings for $2.50 and epoxy glue it into the back of the lid. Then put your pod on the end of that. Like this;
Cheers
_________________ 97 EL Fairmont 4l OHC .Silver. |
|||
| Top | |
|||
| TBO240 |
|
||
|
i have fitted a k&N xstream pod and ba intake pipe using pvc pipe and a 22.5 deg bend
![]() ![]() ![]() [img]http://i688.photobucket.com/albums/vv243/TBO240/04032009269.jpg[/img Attachment: 04032009269-1[1].jpg
You do not have the required permissions to view the files attached to this post. |
||
| Top | |
||
| EL__Fairmont |
|
|||
|
![]()
_________________ 97 EL Fairmont 4l OHC .Silver. |
|||
| Top | |
|||
| huggiebear |
|
|||
|
i just looked back through here and realise i havnt posted the way i done it. seems alot cheaper.
i used: EF intake pipe EL corrigated bend from top right corner of the engine bay 1L metho bottle i removed the airbox lid and took out the center snorkel and bracket, i then cut the metho bottle so a 1.5-2inch wide circle and placed it in the pod filter hose and then done the same to the EL intake pipe side, slid the EL pipe through the airbox lid and joined to the EF intake pipe. the reason i used the metho bottle as i wasnt prepared to pay the $30 price tag supercheap was asking for the alloy pipe and since i had it sitting there and works perfect i thought why not. the bottle is very flexable untill you place it inside the hoses then it becomes very firm. never had an issue with it ![]() ![]() and when its complete no one would ever know
|
|||
| Top | |
|||
| XFWAGON |
|
|||
|
I will prob' get shot for asking this, but how is that any better than a k&n panel filter if you are still enclosing it in the box?
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 0 guests |