|
| DeTiger |
|
||
|
Hi guys. i want to put the pintara's 4.11 diff into my el xr6 manual. Do i have to get the whole diff or am i able to just get the crown and the pinion. Where in sydney can you get them and for how much. how much would the diff place charge to put them in. Who has done it and how complicated was it.
thanks |
||
| Top | |
||
| eboost |
|
|||
|
i have done it. We did a rush job, didnt set clearances and they lasted bout 3 months and now whine like a pom!
I have another set which i scored for free so i will be taking my time this time. If your asking you shouldnt be doing it, but diff places make a killing on fitting these. They'll most likely charge you $200 for gears plus $300 labour! |
|||
| Top | |
|||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
eboost wrote: i have done it. We did a rush job, didnt set clearances and they lasted bout 3 months and now whine like a pom! I have another set which i scored for free so i will be taking my time this time. If your asking you shouldnt be doing it, but diff places make a killing on fitting these. They'll most likely charge you $200 for gears plus $300 labour! probably more. then there is bearings and a pinion seal. the reason they charge like they do is because people expect a good job and a warranty. |
||
| Top | |
||
| eboost |
|
|||
|
diff gears are very hard to get right.
|
|||
| Top | |
|||
| metasaiah |
|
|||
|
I heard that the Pintara gears fit the single-spinner 3.08 diff. Is this B.S.?
I'd rather get an LSD than actually go to the trouble of fitting 4.11's into my single-spinner, but just curious anyhow.
_________________ EF2 Fairmont Ghia. AU2 engine running EF gear. Intake, exhaust, injection etc; 8" rear stockies with 265/50R15 rubber. Shiftkitted auto, J3, custom grille and dash cluster and lots of other useless crap... |
|||
| Top | |
|||
| DeTiger |
|
||
|
Instead of getting pintara's 4.11 diff i ended up getting skylines 3.89, but i have still not put it in. Will probab;y put it in next week.
|
||
| Top | |
||
| Dr_Hoon |
|
||
|
we did the diff in my ED XR6 for Zoom with DiffTrans out in western Sydney, that should be coming out in a few months I think.
they are very good and could sought you out with 4.11 gears and an LSD shim job
_________________ BF XR6 Ute,ED XR6 Manual (SOLD),XD 4V 351 toploader 9in |
||
| Top | |
||
| DeTiger |
|
||
|
How much did it cost u to put it in. What did u put in ur ED, and how does it go now. Thanks
|
||
| Top | |
||
| Dr_Hoon |
|
||
|
i'd have to check my notes again to get the exact price but it was around $400 or something
ED is essentially stock! I have BBM and thermos and stuff ready for a round of simple DIY upgrades but have no time in the last few months. The plan was to fit a simple bolt-on supercharger kit or something. But I am actually looking at selling it in the not too distant future and buy something later model as my daily. I have my XD that is my project but that is still in Perth and need to sort my s**t out with a new daily first.
_________________ BF XR6 Ute,ED XR6 Manual (SOLD),XD 4V 351 toploader 9in |
||
| Top | |
||
| Dr_Hoon |
|
||
|
Say that Glen from Zoom sent you!!!!!!!!!!!!!!!!!!!!!!!
LSD Shim Cost (what work they did on my car) LSD hemisphere machining $132.00 LSD diff oil $22.00 Labour $264.00 Total $418 DiffTrans (02) 4577 8200 38 Fairy Rd South Windsor NSW 2756 other prices: Glen from DiffTrans gave us the following run down on prices you’d expect to pay for diff upgrades and rebuilds from mild to wild. - A good second hand crown wheel & pinion that has been re-lapped ranges from $220.00 to $330.00 - A new crown wheel & pinion ranges from $550.00 to $770.00 - Rebuilt 28-spline 4-pinion LSD Hemisphere is $550.00 - A new 28 spline 4-pinion LSD Hemisphere is $770.00 - DiffTrans can also supply a KAAZ LSD Hemisphere which is race type or serious street use for $1650.00 - By the time this goes to print, they will have the Detroit True Trac LSD hemisphere for $1595.00 - DiffTrans can also make up new Holden Commodore VL Turbo axles to suit from $360.00 - Lastly, DiffTrans can either supply a complete 31-spline 4-pinion LSD hemisphere or parts to convert your hemisphere.
_________________ BF XR6 Ute,ED XR6 Manual (SOLD),XD 4V 351 toploader 9in |
||
| Top | |
||
| DeTiger |
|
||
|
Im going to go to smithfield to the guy that Crescent motorsport sent me to. He said itll cost me $300 and he should be able to do it on either tuesday or wednesday. Thanks for all the info mate
|
||
| Top | |
||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
$300?
so i assume no new bearings, or a LSD?..... do the job once, might as well do it properly |
||
| Top | |
||
| Dr_Hoon |
|
||
|
yeah, the smithfield place isn't bad either
but, yeah, do it properly. I used to have an esky that blew diffs left right and centre, it was an epic pain in the a** to keep changing them. Now, of course, I do less burnouts, but it would still be better to get the diff overhauled.
_________________ BF XR6 Ute,ED XR6 Manual (SOLD),XD 4V 351 toploader 9in |
||
| Top | |
||
| DeTiger |
|
||
|
Ive already got lsd on my EL XR6 but he said hes gonna do eerything anyway. I told him that i need the diff to be strong as the turbo is going on soon so need to be able to take the power. he said not to worry. and he sadi the price. Probab;y cheap beceuse he knows Joe from CMS, and joe sent me there.
|
||
| Top | |
||
| elrob |
|
||
|
i got a 75 series lsd laying around can i use side gears out of a 78 series to make it 28 spline???
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 46 guests |
