|
| XD VAN 82 |
|
|||
|
Shifteh wrote: 80 grit , then all the way through to 2000 grit sand paper , all done by hand ill have to have a crack at it on the TX5 lots of work but it does look good
_________________ Daily: 1994 EF Falcon GLI, few mods with many more planned. |
|||
| Top | |
|||
| Shifteh |
|
||
|
show a pic of the metal you want to polish. if its like rough , porus hit it with a fcirular /orbital sander with some heavy paper to flatten the metal out
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| lukey1990 |
|
||
|
Hey Chris text back lol.
How's the block going?
_________________
|
||
| Top | |
||
| XD VAN 82 |
|
|||
|
how did you go with the bottom end?
_________________ Daily: 1994 EF Falcon GLI, few mods with many more planned. |
|||
| Top | |
|||
| lukey1990 |
|
||
|
Apparently he's waiting for the engine shop to get some pistons..
_________________
|
||
| Top | |
||
| XD VAN 82 |
|
|||
|
lukey1990 wrote: Apparently he's waiting for the engine shop to get some pistons.. so the block i gave him was ok then?
_________________ Daily: 1994 EF Falcon GLI, few mods with many more planned. |
|||
| Top | |
|||
| lukey1990 |
|
||
|
XD VAN 82 wrote: lukey1990 wrote: Apparently he's waiting for the engine shop to get some pistons.. so the block i gave him was ok then? I would hope so if he's spending all that money on it 
_________________
|
||
| Top | |
||
| XD VAN 82 |
|
|||
|
lukey1990 wrote: XD VAN 82 wrote: lukey1990 wrote: Apparently he's waiting for the engine shop to get some pistons.. so the block i gave him was ok then? I would hope so if he's spending all that money on it same here as that block was in unknown cond hence why i gave it away
_________________ Daily: 1994 EF Falcon GLI, few mods with many more planned. |
|||
| Top | |
|||
| lukey1990 |
|
||
|
Yeah, well I think he had an engine shop take a look at it.
_________________
|
||
| Top | |
||
| Shifteh |
|
||
|
its been a whl!e since i last posted
philip young has mesured the block and said t5her might be a bit of fouling at 20thou so hes taking it to 40thou overbore pistons are being orderd 
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| XD VAN 82 |
|
|||
|
Shifteh wrote: its been a whl!e since i last posted philip young has mesured the block and said t5her might be a bit of fouling at 20thou so hes taking it to 40thou overbore pistons are being orderd good stuff so that block turned out to be useable then? when you recon the ef will be running?
_________________ Daily: 1994 EF Falcon GLI, few mods with many more planned. |
|||
| Top | |
|||
| lukey1990 |
|
||
|
It's about time you posted back here
 Done anything else to it?
_________________
|
||
| Top | |
||
| Shifteh |
|
||
|
new pistons
 block after hotbath  
_________________ Crank Assembly balanced, HV oil pump, ACL Trimetal bearings, "1 extra oil clearance taking to around 0.0650-0.0700 on mains and big ends, Moly rings,, Xr6 Cam, POD ( Possibly oversize injectors), Block, Head, Timing cover, belt idler, Alternator,painted in ford light blue |
||
| Top | |
||
| lukey1990 |
|
||
|
Looks good. It'll look even better when it's in the engine bay
_________________
|
||
| Top | |
||
| thepistonhead |
|
|||
|
Hey mate, finally found your thread. Good stuff you got going.
Manage to find my build thread? haha Where do you get your work done?
_________________
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 6 guests |
