|
NCIILANE |
|
|||
|
castlegreyskull wrote: mick you shall regret that buy. They are hopless. wouldnt woorth pissin on.
You posting whilst on the piss again ![]() ![]() ![]()
_________________
|
|||
Top | |
NCIILANE |
|
|||
|
OK, You were right
![]() ![]() ![]() Lesson Learnt! ![]() ![]()
_________________
|
|||
Top | |
NCIILANE |
|
|||
|
Here is a pic of my half-assed attempt to fit a pod filter, and also a couple of pics of the damaged airbox lid. I managed to get my hands on a K&N service kit off ebay for $26 includes post
![]() ![]() Fancy a mini cruise to liverpool KK's friday night Ben? I'll probably be going for a run down to meet up with Matt, might as well make a cruise out of it eh! ![]() ![]() ![]() ![]()
_________________
Last edited by NCIILANE on Sat Jan 31, 2009 9:34 pm, edited 1 time in total. |
|||
Top | |
DARTHVADER |
|
|||
|
Gday NCIILANE, Your ride is superb, rims look beaut on the Lane. I dont mean to be picky mate but your Tyres are on the wrong sides. The direction of the tread tells me the wheels should be swapped out side for side. But please correct me if im wrong.
I do look forward to future pics
_________________ AUIII, PACEY 4499's, MAGNIFLOW CAT, 2.5" ZORST, 17X8" AUII XR RIMS....otherwise all factory! |
|||
Top | |
NCIILANE |
|
|||
|
Hmmmm! You could have something there
![]() ![]() Good pick-up mate. I have been driving around on them for 6 months and you're the first to notice ![]() ![]() ![]()
_________________
|
|||
Top | |
Bsjenko |
|
|||
|
![]() ![]() KK friday night, no good i will be in canberra. And i told you about the filter didnt i ![]() ![]()
_________________ The Lane Lives.... Finally!!!! |
|||
Top | |
NCIILANE |
|
|||
|
![]() ![]() ![]() It's important to learn by your mistakes, and every day you learn something new is a good day! So all is good ![]() Enjoy your trip to Canberra, I'll probably still go for a run to KK's or Harry's (same place???) as svo-matt has lost his but terroristghia has one for me ![]() It was still a nice lookin filter, even if I couldn't get it to fit ![]()
_________________
|
|||
Top | |
Bsjenko |
|
|||
|
Mate why dont you go to the wreckers, they would have one for sure, and it would be a hell of a lot cheaper than going down to sydney.
Try rathmines wreckers, they are damn good, and cheap as chips. Oh, and yes i do like a few ales ![]()
_________________ The Lane Lives.... Finally!!!! |
|||
Top | |
NCIILANE |
|
|||
|
Cheers for the tip Ben, but the boys at the Koala park show were telling me about the Friday night meets at Harry's and now I have an excuse to go for a run and have a Harry's pie
![]() ![]()
_________________
|
|||
Top | |
huggiebear |
|
|||
|
looking good cheif... i like where your going with this... dont worry about the tyres just reverse everywhere and you will be fine... save the k's on the cluster too
|
|||
Top | |
NCIILANE |
|
|||
|
huggiebear wrote: looking good cheif... i like where your going with this... dont worry about the tyres just reverse everywhere and you will be fine... save the k's on the cluster too
![]() ![]()
_________________
|
|||
Top | |
NCIILANE |
|
|||
|
Update on the tyre saga! I was 1/2 right, only had two on the wrong way. I was so excited when I received my wheels that I didn't even consider that they had a certain rotation
![]() Also fitted new spring clips to airbox today. Waste of money they turned out to be ![]() ![]()
_________________
|
|||
Top | |
BuNtEr |
|
||
|
NCIILANE wrote: Update on the tyre saga! I was 1/2 right, only had two on the wrong way. I was so excited when I received my wheels that I didn't even consider that they had a certain rotation
![]() Also fitted new spring clips to airbox today. Waste of money they turned out to be ![]() ![]() need a pop off valve, like they do for Blowers so if they back fire you dont end up with a big mess.
_________________ BANNED |
||
Top | |
NCIILANE |
|
|||
|
I'm working on a one way valve that will be connected to the point where the big dog turd (donut) is normally. I'm thinking of using a 30mm conduit cap and cutting out 2 sections in the lidand then pop rivetting a piece of rubber over it. Bit hard to explain how I picture it but I will post up pics and instructions if it works
![]() This is where the turd normally sits ![]() ![]() ![]()
_________________
Last edited by NCIILANE on Sat Jan 31, 2009 9:37 pm, edited 1 time in total. |
|||
Top | |
Tezza Bear |
|
|||
|
NCIILANE wrote: I'm working on a one way valve that will be connected to the point where the big dog turd (donut) is normally. I'm thinking of using a 30mm conduit cap and cutting out 2 sections in the lidand then pop rivetting a piece of rubber over it. Bit hard to explain how I picture it but I will post up pics and instructions if it works
![]() This is where the turd normally sits ![]() ![]() <a href="http://s285.photobucket.com/albums/ll41/micknkell/?action=view¤t=100_3244Large.jpg" target="_blank"><img src="http://i285.photobucket.com/albums/ll41/micknkell/100_3244Large.jpg" border="0" alt="Photobucket"></a> Mate shes lookin good, if u want a neater look EB1 V8's don't have the donut (dogturd) so if u can get the intake pipe out of a series 1 it would look neater or i hear some center caps fit in the hole nicely.... ![]() ![]()
_________________ |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 17 guests |