Fordmods Logo

Project XG-FPV DOHC Barra 182 

 

Page 26 of 30 [ 449 posts ] Go to page Previous  1 ... 23, 24, 25, 26, 27, 28, 29, 30  Next

 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Fri Feb 21, 2020 9:14 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

johnnyeHCF wrote:
Hey guys, so some times you can get lucky, found a aluminum fuel cell on Gumtree and it was hard to tell how big it was-the guy was busy and for $50 it looked worth it no matter what the size was,so went and got it and Wow it is bloody big-nice thick (not too thick) aluminum and really good welds,looks to be for a carburetor set up with a fuel gauge sender has a drain and breather etc...



So after pulling out the fuel level sender I had a look inside with the torch and looks really good on the inside-but I think this may have come from a circle track race car as it has a baffle built in to the tank,2 U shape peices and the U's face the same way with a hole in one,bloody interesting hey!

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Thu Feb 27, 2020 7:05 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

So have finally got around to tack up the transmission cross member once I worked out the correct height and angle etc...but forgot to do the crush tubes in the cross piece no biggy -will knock one side off get them in position and give them a slight crush in the press to lock them in place and then retack,then I can pull it out clamp it flat and fully weld it and add the other crush tubes in the spacer pieces,but looked like it will work well,may add some gussets if necessary too.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Thu Feb 27, 2020 8:26 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

Fuel system has been vague to say the least, but am going to be using the dual 044 surge tank filled from the fuel cell via a high flow low pressure lift pump 180 lpm and a billet fuel rail which can be fed from both ends and has a return in the middle which will go to a EPMAN fuel regulator and will all be AN6 for now. Am making my own fuel cell pump hanger for the fuel cell.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Fri Feb 28, 2020 9:24 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

johnnyeHCF wrote:
So have finally got around to tack up the transmission cross member once I worked out the correct height and angle etc...but forgot to do the crush tubes in the cross piece no biggy -will knock one side off get them in position and give them a slight crush in the press to lock them in place and then retack,then I can pull it out clamp it flat and fully weld it and add the other crush tubes in the spacer pieces,but looked like it will work well,may add some gussets if necessary too.



Went to the bolt shop to get some hardware for the trans mount and managed to get some shanked screw cap bolts to suit the poly mount with nylock nuts for both top and bottom bolts.As I can't have threads running inside the bushes of the poly mount. Very solid mounting now.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Mon Mar 02, 2020 8:08 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

So crush tubes,initially I only had some really thick tube stuff which for me is better used elsewhere,and then found one of my old small floor jack handles and cut a test piece and was perfect (same thickness as the tube I was using) so I cut 6 pieces slightly oversized and then slowly grounded them to a perfect fit in the tube,then I made a tool out of wood to cut the groove for the seam weld inside the tube and to hammer them in place,doing it this way I don't need to worry about tack welding them in place.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Mon Mar 02, 2020 11:35 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

Have all 6 crush tubes done and drilled the access holes for the upper trans bolts.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Sat Mar 07, 2020 7:37 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

Hey guys! so still going with this damn thing- but getting stuff done,got a 1/8 NPT to AN4 adapter to run oil feed from the sandwich plate (it's only a journal bearing turbo so doesn't need alot of oil) and got some proper silicone heater hose for the coolant feed for turbo,so I still need to weld the AN10 on the hot side heater pipe-the small outlet is for the turbo then goes back to the top of the radiator on the driver's side.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Sat Mar 14, 2020 5:01 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

So have got the trans mount in the correct position and have it fully welded (just welded it myself with the gasless mig) and it turned out really good-strong as as I tested it by smashing it on my Ibeam anvil on both sides and nothing moved.so I gave it a etch prime and some paint-let it dry overnight and just put it on then which went smoothly and it seems strong as hell!

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Sun Mar 15, 2020 7:59 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

So made a start on the dump and side exit and so far should go okay once I get the hole sorted (inner)and the hole through the driver's side gaurd.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Thu Mar 19, 2020 7:17 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

SOOOoooooo...... I used the only bits of TP we had left (the cardboard rolls) and made a wastegate adapter to work out where the WG need to be to clear the drag link & pitman arm,once that was sorted I cut the length needed off the screamer pipe 5.5cm and used the 2 WG flanges that came with the WG and tacked it in place and did a test fit which clears everything nicely.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Sun Mar 22, 2020 9:26 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

So I thought I'd take a picture of the hot side-n/a manifold turbo,wastegate,dump pipe etc........before I put it on fully sealed.
Luckily this won't be driven on the street as it would not last long-the sheer weight of it together is massive so first pothole you hit I think you'd be I trouble. But on an off trailer and track should be okay,will be looking for a better manifold later for sure.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Mon Mar 23, 2020 4:27 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

Have finally received my AN10 90's from China of all places have never felt so apprehensive about opening a package!

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Fri Mar 27, 2020 8:25 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

So got a few things done,like the AN10 coolant lines/heater pipes done,the catch can,cut the inner part of drivers front gaurd for the side exit,also found a new problem with the engine mounts again as the sump is sitting on the front of the k frame just on the lip which I'll have to cut and there is maybe 5mm gap from the inlet manifold to the passenger side strut tower which I don't know if it's going to be a problem with the engine and gearbox fairly solid.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Mon Apr 06, 2020 8:11 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

Just getting stuff done-slowly,have ordered a XR6T MAP sensor and the exhaust manifold center flange gasket,so whilst waiting got the manifold wire wheeled and sanded and cleaned with acetone (this stove paint stipulates that you can only use acetone to prepare for paint,no thinners or prep wash etc..)then painted with Stove Bright high temperature stove paint and can also be used for engine manifolds and mufflers etc,followed the directions and paint went on really nice compared to the VHT paint.

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
 
 Post subject: Re: Project XG-FPV DOHC Barra 182
Posted: Tue Apr 07, 2020 8:30 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 880

Joined: 16th May 2012

Gallery: 16 images

Ride: EF-XR6/XG-6/XE-V8- project

Nearly have all the gaskets needed for the hot side,just waiting on the troublesome centre manifold flange gasket and need another 38mm 2 bolt wastegate gasket,also got a stainless steel mig reel and should have plenty of argon left to weld the wastegate adapter,also need to weld out the dump pipe fully too (mild steel though).

You do not have the required permissions to view the files attached to this post.

 

_________________

XG DOHC-BARRA 182/Turbo kit/20% Underdrive and BA 4-SPEED + Tiptronic shifter

https://youtube.com/channel/UCaRUQ10of3FlOuSpvfapOtA

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 26 of 30  [ 449 posts ]  Go to page Previous  1 ... 23, 24, 25, 26, 27, 28, 29, 30  Next

Who is online

Users browsing this forum: No registered users and 18 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Fri Mar 29, 2024 6:54 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names