|
mrrabbit |
|
||
Age: 34 Posts: 24 Joined: 14th Jan 2007 Ride: AUII XR6, BMW 528i, XF Ute Location: Pt Lincoln |
gday my prob is that i hav a 3.9 cpi 5spd in an xf pannelvan and it uses 1l per 2kms yes 2kms i hav a 350 holley that i am wanting 2 put on now i know i can use the cpi manifold but i wil have 2 weld the existing cpi holes up and tap new ones 2 suit. I am wondering if anything else needs doing 2 make it carby
|
||
Top | |
dacoffee |
|
||
|
mrrabbit wrote: gday my prob is that i hav a 3.9 cpi 5spd in an xf pannelvan and it uses 1l per 2kms yes 2kms i hav a 350 holley that i am wanting 2 put on now i know i can use the cpi manifold but i wil have 2 weld the existing cpi holes up and tap new ones 2 suit. I am wondering if anything else needs doing 2 make it carby i do maintenance for a living and to weld the holes and tap new ones, hmmmmm i can weld but you talking cast and aluminium you dreaming. i never bother with cast alloy, cast steel yes i can weld that and its hard to get it right. if you do try you need ac stick welder with special rods |
||
Top | |
mitchell g |
|
||
|
i though that you would just change the manifold from an efi one to a carby one
|
||
Top | |
TROYMAN |
|
||
|
mrrabbit wrote: gday my prob is that i hav a 3.9 cpi 5spd in an xf pannelvan and it uses 1l per 2kms yes 2kms i hav a 350 holley that i am wanting 2 put on now i know i can use the cpi manifold but i wil have 2 weld the existing cpi holes up and tap new ones 2 suit. I am wondering if anything else needs doing 2 make it carby do you mean the stud holes in the manifold where the throttle body bolts on?? if so it should be the same bolt patturn as the xe/xf webber carb?? if it is you can get a webber to holley addaptor plate... |
||
Top | |
fairmont54 |
|
||
|
i can tell you that someone? makes adapter plates from th 3.9cfi (throttlebody injection) manifolds to holleys or webbers but ya gotta remember to use the centerpoint manifold gasket (doesnt have the injectoe cut outs) they can be used on anything up to au
Last edited by fairmont54 on Fri Dec 04, 2009 6:58 pm, edited 1 time in total. |
||
Top | |
fairmont54 |
|
||
|
the computer is gona think its got no injection pulse. that could affect the spark if your runnin ea computer you should maybe think of going back to xf computer for spark control and xf dizzy if ya can havent done this but reckond it could be done
|
||
Top | |
low_ryda |
|
|||
|
you just need an older dizzy and as troyman mentioned a weber to holley adapter plate which could also cause bonnet clearance issues. going back to full mechanical advance etc you don't need ecu spark control. your retrofitting not trying to re-invent to wheel. it's a weapon of choice for lower category speedway cars.
dacoffee wrote: mrrabbit wrote: gday my prob is that i hav a 3.9 cpi 5spd in an xf pannelvan and it uses 1l per 2kms yes 2kms i hav a 350 holley that i am wanting 2 put on now i know i can use the cpi manifold but i wil have 2 weld the existing cpi holes up and tap new ones 2 suit. I am wondering if anything else needs doing 2 make it carby i do maintenance for a living and to weld the holes and tap new ones, hmmmmm i can weld but you talking cast and aluminium you dreaming. i never bother with cast alloy, cast steel yes i can weld that and its hard to get it right. if you do try you need ac stick welder with special rods thats why your not a welder. and not much of a maintainence bloke by the sounds of it either. i can weld up used combustion chambers/corroded water jackets of cast ally cylinder heads along with thousands of other people. you don't need an ac stick to use good cast rods, just talent. your better off tigging cast steel,staino & ally and brazing cast iron. and if your going to retap, instead of being a n00b and filling the hole with bird shyte you would weld a piece of rod in with good prep then re drill & tap.
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
Top | |
milo 302 |
|
||
|
You can get a 2 or 4 barrel carby manifold to suit, aussie speed make them.
|
||
Top | |
briney |
|
|||
|
why not just try and fix the efi ? leaking injector o rings can do this, as well as the pressure regulator being stuck. is the vac line on the map sensor ? does it blow black smoke ?
_________________ vote for pedro ? f**k pedro, f**k him up his stupid a***hole. |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 4 guests |