|
Stealth6 |
|
|||
|
I was wondering if any six speed gearboxes would bolt onto an XG without major modifications. The 5 speed is fine, but this Ute does many long trips travelling at about 130kmh and it revs at about 3000. Which i think is quite good for that speed, but would like to bring it down a bit if that's even possible, and save a bit of fuel. (not that its that bad on fuel anyway) has anyone done or heard of this, any suggestions?
_________________ Yep, I don't know what to write here... |
|||
Top | |
rustyeb1991 |
|
||
|
try swapping diff for 2.92-1 and see how that goes before committing to a 6 speed swap, had an xd with 2.77-1 diff and t5 and that was a bit too tall, wasn't worth using 5th unless doing 150km or above. (hypothetically of course) for legal reasons lol.
|
||
Top | |
Stealth6 |
|
|||
|
thanks rusty. I think i might go with 2.92-1. Actually makes a lot more sense than gearbox swap. Are the diffs that hard to change?
_________________ Yep, I don't know what to write here... |
|||
Top | |
EF_wanabe |
|
||
|
So if we use a VT-VZ LS1 box , apart from the speedo issue's i have read, tail shaft shouldnt be all to hard get a custom one
What else am i looking at on fitting ? , which malwood kit would i need for the clutch pedal "conversion" ? |
||
Top | |
cjh |
|
|||
|
The early EA's with T5's had 2.92 diff gears.....I had one.....the auto's ( BW51's ) had 2.77's.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
Top | |
EF_wanabe |
|
||
|
cjh wrote: The early EA's with T5's had 2.92 diff gears.....I had one.....the auto's ( BW51's ) had 2.77's. ahh yes yes obviously 4.11s in the diff or some type of gear change I have read on here a 1/4 mile time of a AU XR8 with a T56 doing a shocking time for some reason 2.2sec 60ft time or something which i expected to be a lot quicker maybe the first and 2nd gears in the T56 are different ratios then the T5s ? |
||
Top | |
cjh |
|
|||
|
Early T5's were 3.50:1 first gear, and the later ones were 3.25:1....these are 6 cyl ones.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
Top | |
89.SVO |
|
|||
Age: 35 Posts: 3382 Joined: 11th Mar 2008 Ride: EA SVO, AU2, Toyota Crown Location: Bendigo |
my EA was 3 speed but now T5. T5 with 2.77 gears it does about 1900 at 100km/h
_________________ Daily driver: 2010 Toyota Crown hybrid 3.5L V6 hybrid. 254kw. |
|||
Top | |
Stealth6 |
|
|||
|
Lol. I'd forgotten all about this thread... 89.SVO thats weird. My XG with t5 and 3.27 or 3.23 whatever the f**k it is also sat on 1900 at 100kmh same as you with 2.77... And it had a stupidly short first gear that was completely useless unless hill starting on a near vertical hill... Maybe Ford screwed up with me XG and the gearbox was made of spare parts from various different models lol.
_________________ Yep, I don't know what to write here... |
|||
Top | |
89.SVO |
|
|||
Age: 35 Posts: 3382 Joined: 11th Mar 2008 Ride: EA SVO, AU2, Toyota Crown Location: Bendigo |
my speedo is probably out. gearbox come out a ea with 3.08 diff gears
_________________ Daily driver: 2010 Toyota Crown hybrid 3.5L V6 hybrid. 254kw. |
|||
Top | |
alfy |
|
|||
|
least you dont have 3.45's and sit on 2700 at 110 just before the cam powerband and suck fuel like a lord like my old Ghia did... id hate to see what 4.11's are at.
_________________ 2021 V6 Manual Amarok - 245kw/750nm - many goodies |
|||
Top | |
ef_falcon_95 |
|
|||
|
EF_wanabe wrote: So if we use a VT-VZ LS1 box , apart from the speedo issue's i have read, tail shaft shouldnt be all to hard get a custom one What else am i looking at on fitting ? , which malwood kit would i need for the clutch pedal "conversion" ? If your going to use a t56 from a ls1 you'll need to swap the input shaft over from a Tuet 6000 which is a t56 from a vz 6L as its shorter . Or find a Tuet 6000 like I did . You won't need a custom tail shaft I have a Tuet 6000 vz 6L t56 and my standard tail shaft fits perfect . The box is only like 40 mm longer than a t5 . Shifter came up in the normal spot just had to trim 20 mm from the trans tunnel . I made my hydraulic pedal from a ba hydraulic clutch pedal assembly . Which is exactly what malwood do but mine was $600 cheaper lol
_________________ El XR6 Turbo |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 7 guests |