|
capare |
|
||
|
Hello, Its been long over due so I thought I'd post up my own build thread!
It started about 3 years ago, I'd saved up a decent ammount of cash and was on the look for my childhood dream car. Armed with carsales I hunted for a blue EL XR8 5 speed manual with the tickford kit. Not to long after searching I found the car I wanted! It had 200000ks mint condition with extractors and single 2.5in exhaust, it also came with a set of FR17 simmons rims . After I bought the car I started to dream up what I wanted to do with it. I decied to do a topend rebuild. So I bought a topend off a fellow modder witch consisted of Edelbrock RPM 2, comp cams xe282hr, 1.7 trickflow roller rockers and world sportsman heads. but after having realised the heads were to big for my baby 302 windsor i decieded to do a stroker build. I started to do some research on stroker kits and decided if i was going to spend the money I'd do it properly, so i bought a dart shp 363ci short block. Then I sold my RPM2, cam and rockers. I then looked at a new manifold and decided on the Trickflow Rseries 90mm bore, a comp cams XFI 248hr, comp 1.6 roller rockers and an accufab 85mm throttle body. :engine: Dart 363ci bottom end Custom fabricated sump Hi volume oil pump Pionner harmonic balancer New water pump Roller master timing chain world Sportsman ported heads flow tested to 660hp@ 600tho of lift Comp Cams XFI 248hr stroker cam Trickflow hydraulic roller lifters Titanium push rods Comp Cams 1.6 roller rockers Ford racing rocker covers Trickflow Rseries 90mm bore intake manifold Accufab 85mm throttle body 90mm lightning MAF 42lb injectors SCT switch chip BBK hi flow fuel rails malpassi fuel presure regulator screaming deamon coil, TFI modual and 10mm leads MSD ignition cap Drivetrain: Spec twinplate organic clutch and billet aluminnum flywheel Gforce T5 with billet case and upgraded main shaft Billet short shifter Fully rebuilt diff Exhaust: Diffilpo 4 into 1 1.7/8in custom extractors 3in collectors Duel 3in cats Custom duel 3in ehaust x piped with xforce mufflers then duel 2.5in up and over the diff Should be getting the car back in the next 2 weeks form CMS Chers Matt Last edited by capare on Wed Dec 07, 2011 11:11 pm, edited 3 times in total. |
||
Top | |
capare |
|
||
|
pics
You do not have the required permissions to view the files attached to this post. |
||
Top | |
DarkELxr6 |
|
|||
|
Gorgeous car mate, can't wait to what sort of numbers this baby reels off. Are you heading towards the supercharging path? Or keeping her N/A? This is going to be an epic build thread
Subscribed
_________________ Le Mans Red EL XR6 - 152rwkw |
|||
Top | |
capare |
|
||
|
DarkELxr6 wrote: Gorgeous car mate, can't wait to what sort of numbers this baby reels off. Are you heading towards the supercharging path? Or keeping her N/A? This is going to be an epic build thread Subscribed thanks DarkELxr6! I'm planing on keeping it N/A for the time being as it has 10.5.1 comp. It should put down some decent power! Supercharging who knows what the futer holds. Cheers Matt |
||
Top | |
TerroristGHIA |
|
|||
|
Bout time Matty.
Looks good as always. Saw you sump the other day, came up very trick. Need to do something similar to mine. Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
capare |
|
||
|
TerroristGHIA wrote: Bout time Matty. Looks good as always. Saw you sump the other day, came up very trick. Need to do something similar to mine. Brett Thanks Brett! I heard you were having oil preasure issues I hope you get that sorted out. Cheers Matt |
||
Top | |
capare |
|
||
|
more pics
You do not have the required permissions to view the files attached to this post. |
||
Top | |
alby1 |
|
||
|
Car looks hot mate, wheels are just perfect, Will be keeping an eye on this for sure.
Where about are you in NSW Al
_________________ EL XR8 II Manual, Ported GT40P's, E303 cam, Au220TB, 70mm MAF, HiFlo Cats, Tune (215rwkw) and some bigger brakes |
||
Top | |
capare |
|
||
|
alby1 wrote: Car looks hot mate, wheels are just perfect, Will be keeping an eye on this for sure. Where about are you in NSW Al Thanks mate! I couldnt agree more about the rims looking hot! Im out liverpool way mate. Cheers Matt |
||
Top | |
Iveco550 |
|
|||
|
omg this el is hot as
_________________ Your commodore has just as much torque as my wheel nutts |
|||
Top | |
XRCIST |
|
|||
|
WOW.....just WOW
Awesome car and awesome build. Cant wait to see it when its all put together. I would love to do a 363 build in an EL or AU3 XR8 in the future!! 10.5:1 comp would be perfect with a an intercooled vortech down the track too
_________________
|
|||
Top | |
WARMACHINE |
|
||
|
Sorry but n/a 6cylinders are more powerful...
|
||
Top | |
Johnson stroker |
|
|||
|
RAPTOR_XR8 wrote: Sorry but n/a 6cylinders are more powerful... I challenge your claim, and raise you one Laser. Matty, s**t looks so cash brah...
_________________
|
|||
Top | |
ebgtjames |
|
||
|
I didn't know Diffilpo did 4 into 1 1.7/8in extractors, the pair I had were 1.3/4in
Good looking car, will be watching this for sure! |
||
Top | |
TerroristGHIA |
|
|||
|
Its a similar set up to mine. Difillipo supplied the pipes as 1 7/8 as a kit, it is then assembled at this end.
Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 7 guests |