|
EF_96_XR |
|
|||
|
Ok so what was originally just going to be the repair of a timing chain rattle has turned into a full rebuild, im unsure of exactly what will be done to the engine but current plans and new highcomp pistons, head work, cam, injectors and ecu but i still have to sort out exactly what im going to do with it before anything is certain
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor Last edited by EF_96_XR on Sun Dec 02, 2012 8:02 pm, edited 10 times in total. |
|||
Top | |
EF_96_XR |
|
|||
|
Attachment: Engine rebuild 1.jpg Attachment: Engine rebuild 2.jpg Attachment: Engine rebuild 3.jpg Attachment: Engine rebuild 4.jpg Attachment: Engine rebuild 5.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
EF_96_XR |
|
|||
|
Attachment: Engine rebuild 6.jpg Attachment: Engine rebuild 7.jpg Attachment: Engine rebuild 9.jpg Attachment: Engine rebuild 10.jpg Attachment: Engine rebuild 11.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
EF_96_XR |
|
|||
|
Attachment: Engine rebuild 12.jpg Attachment: Engine rebuild 13.jpg Attachment: Engine rebuild 14.jpg Attachment: Engine rebuild 15.jpg Attachment: Engine rebuild 16.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
EF_96_XR |
|
|||
|
Attachment: Engine rebuild 17.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
EF_96_XR |
|
|||
|
Thought i would have a go at polishing the inlet manifold while it is off wich is going to be a monumetal efort if when i finish it lol
Attachment: Inlet 1.jpg Attachment: Inlet 2.jpg Attachment: Inlet 3.jpg Attachment: Inlet 4.jpg Attachment: Inlet 5.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
EF_96_XR |
|
|||
|
After close to two hours of polishing by hand on one spot
Attachment: Inlet 6.jpg Attachment: Inlet 7.jpg Attachment: Inlet 8.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
87SIlude |
|
||
|
Dude. That will take weeks. Get a die grinder amd a little buffing wheel or something.
|
||
Top | |
ef_falcon_95 |
|
|||
|
I thought when u said "rebuild " it would be pistons, rods bottom end stuff.
Are u just fixing up the top end ??
_________________ El XR6 Turbo |
|||
Top | |
bry40l |
|
|||
|
I thought it was the whole engine from the title
_________________ BF XR6 |
|||
Top | |
EF_96_XR |
|
|||
|
Yea i will be getting the bottom end out on a stand and doing pistons ect, i ordered an engine stand through work and it hasnt arived yet and being impatient i started pulling it apart in the car lol, plus im going to gets some mates around to give me a hand to drag the engine up my driveway Hopefully the whole engine will be out of the car next w/e
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
EF Wagon |
|
|||
Posts: 69 Joined: 27th Dec 2006 Ride: EF Wagon Location: Canberra - not as bad as you think |
Good on you for having a go at the work yourself.
It's hard to beat driving a car that you know you've rebuilt the engine yourself. Great pics too.
_________________ 96 EF Wagon, PRINS VSI LPG, Wade 1636, 4480's, Redback zorst, Metalcat, 3 angle valve job, .5mm overbore, hypertec pistons, shaved head (because the head was banana shaped when I brought it), Tickford 16" alloys, KYB shocks, 30mm sway bar, 1 1/2 degrees negative camber, tow bar, roof racks. |
|||
Top | |
EF_96_XR |
|
|||
|
Squeezed in a bit more work before i have to go to work this arvy, just got the centre console, exhaust and tailshaft out.... the exhaust copped the grinder lol but im not using that exhaust again anyway
Attachment: Console.jpg Attachment: Console 2.jpg Attachment: Exhaust.jpg Attachment: Exhaust 2.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
EF_96_XR |
|
|||
|
ok we made some progress today and got the the gearbox and what was left of the engine out of the car, and yes i did clean up the mess i made in front of my driveway lol
Attachment: Rebuild 1.jpg Attachment: Rebuild 2.jpg Ready to drop the box Attachment: Rebuild 3.jpg Attachment: Rebuild 4.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
EF_96_XR |
|
|||
|
Box out
Attachment: Rebuild 5.jpg Attachment: Rebuild 6.jpg Engine out Attachment: Rebuild 7.jpg Attachment: Rebuild 8.jpg Attachment: Rebuild 9.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 96 EF XR6 Factory 5 sp, currently in the middle of building a new motor |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 3 guests |