|
| duvauchellemotors |
|
|||
|
if i order new AU ones will they fit?
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
oh i see..
i just had a better look at the pic.. the one going to the tap is fine... what you need is a ef/el heater hose.. its kind of a s shape hose.. this should allow the pipe to sit lower.. |
||
| Top | |
||
| duvauchellemotors |
|
|||
|
ok cool thanks I think i might just order both new ones
I Assume they are both called heater hoses? I will have to order a EF EL right hand radiator hos aswell then? |
|||
| Top | |
|||
| XR-Lane |
|
|||
|
{USERNAME} wrote: ok cool thanks I think i might just order both new ones I Assume they are both called heater hoses? I will have to order a EF EL right hand radiator hos aswell then? your have a EF EL radiator dont you mate? Do you have a set of thermo fans yet? Its good to see you already have the engine in mate although it would have been easier to bolt on the BBM and accessories to the engine before dropping it in. but you will be alright, its just a bit less room now to play with. did you find out about the bracket and pulley to replace the aircon pump? Josh |
|||
| Top | |
|||
| duvauchellemotors |
|
|||
|
Havnt found out about the pully yet.
I got a new radiator a little while ago and i think it was EB-EF but im not sure. havnt got the thermos yest either. Its not alll going to happen at once but ill slowly get everything i need. cheers I also read the post in the Retrofit Info forum about AU to EBII on the last page and that was a great help because now i know what i need. |
|||
| Top | |
|||
| TROYMAN |
|
||
|
you need to check your radiator..
as eb has a different size lower radiator hose..eb hose is larger diamiter than ef/el.. |
||
| Top | |
||
| duvauchellemotors |
|
|||
|
well this is still an ongoing affair.
I have just got my hands on a large sum of money so i can get back to buisness. I still have a couple of things to clear up: Iv been trying to sort out an EL ECU but they all want the numbers for one could some one help me out with this?????? Also th eBlue back valve Non ov the wreakers or ford seem to know what this is but that ok i can go it and pick it off one they are wreaking but first i need to know where it is???????????? Also im not running A/C and im after an Idler bracket...... I rang up fprd and the guy thier said that EL/EF would be the only models with them and that they are rear.....so i rang aroung a few wrekers and they all had only seen them with AC..........Id hate to have to but an AC pump just so i can run the car and i my cars never had AC so it would be a pain installing it... Thats it .......... For Now |
|||
| Top | |
|||
| duvauchellemotors |
|
|||
|
bump
|
|||
| Top | |
|||
| TROYMAN |
|
||
|
hi
you can use any of the ones below// i was using the 6djb to get the feature of the xr6 timing and fuel map without paying the high price for a xr6 ecu.  6DBB - 1997 EL Fairmont Auto. 6DBD - 1997 EL Auto 3.08 Diff 6DDB - EL Fairmont 6 cyl Auto. 6DJA - 4.0, Auto, Fairmont Ghia (tickford engine) 6DJB - 4.0, Auto, Fairmont Ghia (tickford engine) 6DLE - 4.0L Auto (South african Export) 6DNB - EL Police 4.0L Auto 6TAD - EL XR6 Manual - Revision D 6TBB - Police Spec EL 6TBC - EL XR6 6TBD - EL XR6 Auto - Revision D |
||
| Top | |
||
| TROYMAN |
|
||
|
also the blue/black one way vac valve is located behind the windscreen washer bottle with the bbm solinoid..
|
||
| Top | |
||
| duvauchellemotors |
|
|||
|
oh cool thanks Troy
It looks like i will just have to get an AU A/C and use it as and idler..... Or can i just swap pully's over because i already have two EA-ED series ones...Also can i change pullys over on the P/S pump?? |
|||
| Top | |
|||
| TROYMAN |
|
||
|
{USERNAME} wrote: oh cool thanks Troy It looks like i will just have to get an AU A/C and use it as and idler..... Or can i just swap pully's over because i already have two EA-ED series ones...Also can i change pullys over on the P/S pump?? no the ea-ed aircon pumps are different how they mount..they actually mount about 12mm further back and the belt wont line up.. but if you can get an idler from ef/el(non aircon) you can fit that to the au block.. afaik you can change the power steering pulleys over as the rest of the power steering pump is the same 
|
||
| Top | |
||
| duvauchellemotors |
|
|||
|
ok cool cheers....
I tried getting my hands on an idler for the A/c but no luck..... |
|||
| Top | |
|||
| duvauchellemotors |
|
|||
|
ahha I'v found one..........Its up in Dorkland and the guy wants 90 bucks for it????
|
|||
| Top | |
|||
| duvauchellemotors |
|
|||
|
Ok so i have all my parts now and the only thing to come is my J3 chip witch should be on its way soon
 One question...... Can i put the heater hoses on from the underside of the car?? Cheers |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 0 guests |
