Fordmods Logo

cnc ported heads available from jmm for ea-au 

 

Page 4 of 4 [ 55 posts ] Go to page Previous  1, 2, 3, 4

 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Wed Nov 16, 2011 12:39 pm 
Getting Side Ways
Offline

Posts: 6449

Joined: 11th Nov 2004

DRHEMI wrote:
skidder wrote:
Am I missing something or is that $1600ish bare? And $2250 built? JMM want something over $2000 bare I thought?
Nah not missing anything - just saying VL comparison is high volume thus cheaper - the Ford OHC & Hemi 265 are low volume so its a better comparison

CHI Hemi 6cyl Head $2,250 Street Version complete
CHI Hemi 6cyl Head $2,400 Race Verison complete




The JMM head doesn't have Ferrea valves and Isky springs and retainers.
The CHI hemi head is also new design alloy replacement head. The JMM head is a common cheaply availble head with cnc porting.
You comparrison with the CHI head is apples and oranges.

Anyway, this thread is getting just as f**k in a*** as the one on boostedfalcon.

 

_________________

PERMANENTLY BANNED

Last edited by tickford_6 on Thu Nov 17, 2011 11:44 am, edited 1 time in total.

Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Wed Nov 16, 2011 1:22 pm 
Stock as a Rock
Offline

Age: 28

Posts: 196

Joined: 13th Sep 2011

Ride: EB falcon

Location: Boyne Island
QLD, Australia

i understand what youse are says i really do im just asking because the mod here had done a head for a mates au just to tidy up the casting marks and to be honest it was more ugly when we got it back there was crap everywhere mind you they had hardly touched the casting marks, so i hit it with a sandpaper wheel and do it myself and just left it at that it's been good every sence, anyways i dnt like the mod here they charged me $600 for a set of race valves for the datto, which i had gotten the part number off the net and i could have gotten them for $400 off the net but didnt have a cc to do it. they have a race car they built thats supposed to be one of the quickest unblown vr commies in town but ive never seen it go down the strip nor seen a slip to tell me anything ive seen one lads vr on the dyno push 210kw but it was chipped, tuned, and tricked out wasnt bad for a s**t vr though it did sound good with just 2 hotdogs in the system.
Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Mon Nov 21, 2011 9:57 am 
Fordmods Newbie
Offline

Age: 62

Posts: 7

Joined: 21st Nov 2011

Ride: ford G6E

Location: bendigo
VIC, Australia

bry40l wrote:
does anyone actually know what the price tag is for a machine that will digitize the head and machine it? the one ive herd about is worth upwards of 250,000 imported from america?


I have a Centroid A560 cnc porting machine. You are very close on its price.
We are currently developing ports for NA and turbo/blown applications that are proven and with correct
air speeds for the intended use, not just big numbers with fat lazy ports that work good on the bench
but not on the track.
The flow numbers will be real, not inflated and the prices will be a lot less than what is being advertised at the moment.
You can check our website at WWW.enginedynamics.com.au
We will be releasing a line of these heads very soon.
Rod.
Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Thu Nov 24, 2011 7:08 pm 
Getting Side Ways
Offline

Posts: 2410

Joined: 4th Sep 2006

Location: Sydney
NSW, Australia

AED262 wrote:
bry40l wrote:
does anyone actually know what the price tag is for a machine that will digitize the head and machine it? the one ive herd about is worth upwards of 250,000 imported from america?


I have a Centroid A560 cnc porting machine. You are very close on its price.
We are currently developing ports for NA and turbo/blown applications that are proven and with correct
air speeds for the intended use, not just big numbers with fat lazy ports that work good on the bench
but not on the track.
The flow numbers will be real, not inflated and the prices will be a lot less than what is being advertised at the moment.
You can check our website at http://WWW.enginedynamics.com.au
We will be releasing a line of these heads very soon.
Rod.


Hi Rod,

Can you give us a rough description on what you doing and prices please???

Cheers

 

_________________

Wanted Either Capri/Cortina/XY/XW/XR/XT with tough V8 stroker engine, auto, 9inch, upgraded brakes etc[/SIZE][/size][/color]

Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Fri Nov 25, 2011 9:50 am 
Fordmods Newbie
Offline

Age: 62

Posts: 7

Joined: 21st Nov 2011

Ride: ford G6E

Location: bendigo
VIC, Australia

MICKYYYY wrote:
AED262 wrote:
bry40l wrote:
does anyone actually know what the price tag is for a machine that will digitize the head and machine it? the one ive herd about is worth upwards of 250,000 imported from america?


I have a Centroid A560 cnc porting machine. You are very close on its price.
We are currently developing ports for NA and turbo/blown applications that are proven and with correct
air speeds for the intended use, not just big numbers with fat lazy ports that work good on the bench
but not on the track.
The flow numbers will be real, not inflated and the prices will be a lot less than what is being advertised at the moment.
You can check our website at http://WWW.enginedynamics.com.au
We will be releasing a line of these heads very soon.
Rod.


Hi Rod,

Can you give us a rough description on what you doing and prices please???

Cheers



Yes Mickyyyy,
we have two cnc ports available.
One is for a NA or low boost [10-15 lbs] this has std size valves, an excellent velocity profile and flows at the high end of cfm/sq in of valve throat area.
The other is a bigger valve and larger port with higher flow and will be killer in a higher boost application.
The prices are,
New head casting, $1700 bare and $2175 complete with Crow spring and retainers.
Your head, Inc. reco price $1250 using std springs and retainers and $1480 with Crow springs and retainers.
As with any cylinder head, there are heaps of options and the sky is the limit.
We will be doing a partial cnc chamber because these chambers have horrible pressure recovery and machining the whole chamber to look good will cost power the same as some other cylinder heads.
If anyone needs more info, give me a call on 0354433883.
Rod.
Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Sat Nov 26, 2011 12:35 pm 
Getting Side Ways
Offline

Posts: 2410

Joined: 4th Sep 2006

Location: Sydney
NSW, Australia

AED262 wrote:
MICKYYYY wrote:
AED262 wrote:
bry40l wrote:
does anyone actually know what the price tag is for a machine that will digitize the head and machine it? the one ive herd about is worth upwards of 250,000 imported from america?


I have a Centroid A560 cnc porting machine. You are very close on its price.
We are currently developing ports for NA and turbo/blown applications that are proven and with correct
air speeds for the intended use, not just big numbers with fat lazy ports that work good on the bench
but not on the track.
The flow numbers will be real, not inflated and the prices will be a lot less than what is being advertised at the moment.
You can check our website at http://WWW.enginedynamics.com.au
We will be releasing a line of these heads very soon.
Rod.


Hi Rod,

Can you give us a rough description on what you doing and prices please???

Cheers



Yes Mickyyyy,
we have two cnc ports available.
One is for a NA or low boost [10-15 lbs] this has std size valves, an excellent velocity profile and flows at the high end of cfm/sq in of valve throat area.
The other is a bigger valve and larger port with higher flow and will be killer in a higher boost application.
The prices are,
New head casting, $1700 bare and $2175 complete with Crow spring and retainers.
Your head, Inc. reco price $1250 using std springs and retainers and $1480 with Crow springs and retainers.
As with any cylinder head, there are heaps of options and the sky is the limit.
We will be doing a partial cnc chamber because these chambers have horrible pressure recovery and machining the whole chamber to look good will cost power the same as some other cylinder heads.
If anyone needs more info, give me a call on 0354433883.
Rod.


Rod,


Thanks for the promt reply


Can you go into more detail about the camber and pictures who be great to see.

 

_________________

Wanted Either Capri/Cortina/XY/XW/XR/XT with tough V8 stroker engine, auto, 9inch, upgraded brakes etc[/SIZE][/size][/color]

Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Sat Nov 26, 2011 9:15 pm 
Getting Side Ways
Offline
User avatar

Posts: 659

Joined: 14th Apr 2006

Ride: EF Fairmont Sedan

Power: 180 rwkw

Location: Ferntree Gully
VIC, Australia

Do you have an eseries Mickyyy?

Just curious thats all :)

 

_________________

PROEF 13.46 @ 105.78mph - 1994 Ford Fairmont EF NA 6cyl Man 3.9 diff Sedan
Stock Fuel Pump, 29lb Injectors, JMM Street Series Headers, 2.5" Exhaust, 205rwkw

Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Sat Nov 26, 2011 9:36 pm 
Getting Side Ways
Offline

Posts: 2410

Joined: 4th Sep 2006

Location: Sydney
NSW, Australia

DRHEMI wrote:
Do you have an eseries Mickyyy?

Just curious thats all :)


Yeh ive had a EL and currently have a EF XR6 and did have a EF XR8 347 stroker :D

ford-parts-for-sale-f17/for-sale-17-500-ono-ford-ef-xr8-347-stroker-c4-price-drop-t52704.html

Also had a TE cortina that was mini tubbed, 9inch, coil overs, mini tubbed, 6 point cage, alloy dash that I was building and might have RX3 in my driveway soon :D

I don't do build threads but there u go bud

How does my resume compare :D

 

_________________

Wanted Either Capri/Cortina/XY/XW/XR/XT with tough V8 stroker engine, auto, 9inch, upgraded brakes etc[/SIZE][/size][/color]

Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Sat Nov 26, 2011 10:39 pm 
Getting Side Ways
Offline
User avatar

Posts: 659

Joined: 14th Apr 2006

Ride: EF Fairmont Sedan

Power: 180 rwkw

Location: Ferntree Gully
VIC, Australia

Ahhhh no build threads - pretty good resume lol as posted just curious

Did you have a Stroker ED with plates MEANED at one time

 

_________________

PROEF 13.46 @ 105.78mph - 1994 Ford Fairmont EF NA 6cyl Man 3.9 diff Sedan
Stock Fuel Pump, 29lb Injectors, JMM Street Series Headers, 2.5" Exhaust, 205rwkw

Top
 Profile  
 
 
 Post subject: Re: cnc ported heads available from jmm for ea-au
Posted: Sat Nov 26, 2011 11:37 pm 
Getting Side Ways
Offline

Posts: 2410

Joined: 4th Sep 2006

Location: Sydney
NSW, Australia

No but did it happen to be blue ED with a man o war 347 stroker, gold simmons same car?

Here is my old cortina

http://www.fordaustraliaforums.com/foru ... t-drag-Car

P.S If u can get me a PWR intercooler, radiator and oil cooler for a Mazda RX3 pm me a price...

 

_________________

Wanted Either Capri/Cortina/XY/XW/XR/XT with tough V8 stroker engine, auto, 9inch, upgraded brakes etc[/SIZE][/size][/color]

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 4 of 4  [ 55 posts ]  Go to page Previous  1, 2, 3, 4

Who is online

Users browsing this forum: Google [Bot] and 45 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Mon Dec 11, 2017 5:28 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names