|
| phil545 |
|
|||
|
Nice, i like that galaxy but yes minus the tail lights!
_________________ I hate arriving at my destination as then I have to get out of my car! |
|||
| Top | |
|||
| steveurban |
|
|||
|
jtauelangi wrote: I have just finished a full kit for mine. any pic's 
|
|||
| Top | |
|||
| biggav |
|
|||
|
steveurban wrote: jtauelangi wrote: I have just finished a full kit for mine. any pic's agreed pics or ban
_________________ 4.0lt Balanced Bottom End, ACL Race Internals, Rspec4 Cam, BPT Swichchip, PH4480, 2.5' Lukey, Scorcher Bodykit, T5 Manual frd906 wrote: LOLLOLLOLLOLOLLOLLOLLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOL
|
|||
| Top | |
|||
| jtauelangi |
|
||
|
Guessing i need to upload to photobucket or something to put up. Bare with me.
|
||
| Top | |
||
| jtauelangi |
|
||
|
Ok, This is the way i bought it:
 And this is it at the moment.    Sorry the photos are so big, I'm not sure how to resize them yet. |
||
| Top | |
||
| phil545 |
|
|||
|
Sweet ride!!! i really like that kit mate!
_________________ I hate arriving at my destination as then I have to get out of my car! |
|||
| Top | |
|||
| frd906n |
|
||
|
Nice kit mate
_________________ Daily Driver, Series 1 Au Forte Quote: Posted by Xcabbi, Does it slap or rattle? Rattle is more to do with timing chains and tensioners. Slap is more to do with lifters, rings, bearings or GENIII boat anchors
|
||
| Top | |
||
| biggav |
|
|||
|
not bad at all, guessing its a meshing of FG and BA?
had the simluar idea for the rear so i can have twin tips out the back without having them as dumpers.
_________________ 4.0lt Balanced Bottom End, ACL Race Internals, Rspec4 Cam, BPT Swichchip, PH4480, 2.5' Lukey, Scorcher Bodykit, T5 Manual frd906 wrote: LOLLOLLOLLOLOLLOLLOLLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOL
|
|||
| Top | |
|||
| steveurban |
|
|||
|
nice work
have you got any "square on" shot's ? for a better look at the kit. |
|||
| Top | |
|||
| DallasXR6 |
|
||
|
Thats sweet... You could make some money off that..
|
||
| Top | |
||
| fordfreak ef |
|
|||
|
Well done jtauelangi. kit looks pretty well fit/finished.. -very original work there.
|
|||
| Top | |
|||
| DARTHVADER |
|
|||
|
I love it
 Came up Tip Top mate. Well done.MITCHY
_________________ AUIII, PACEY 4499's, MAGNIFLOW CAT, 2.5" ZORST, 17X8" AUII XR RIMS....otherwise all factory! |
|||
| Top | |
|||
| BF XR |
|
||
|
i think the question we should all be asking is did the xr lip fit straight onto the back
|
||
| Top | |
||
| biggav |
|
|||
|
BF XR wrote: i think the question we should all be asking is did the xr lip fit straight onto the back thats what im thinking it did just with some added length to the sides. is the rear bar plastic or glass?
_________________ 4.0lt Balanced Bottom End, ACL Race Internals, Rspec4 Cam, BPT Swichchip, PH4480, 2.5' Lukey, Scorcher Bodykit, T5 Manual frd906 wrote: LOLLOLLOLLOLOLLOLLOLLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOLOL
|
|||
| Top | |
|||
| jtauelangi |
|
||
|
BF XR wrote: i think the question we should all be asking is did the xr lip fit straight onto the back The answer to that question is 'no'. Hit two problems with fitting the xr lip. 1st one is the obvious, Not quite long enough, toget around this, i had to extend the sides about 15cm, if you look closely at behind the mudflap you will see the extended bit. 2nd was that because the lip sits lower on an xr it wasnt quite wide enough to fit on the bottom of the fairlane rear bar, to fix this i have cut the xr lip in half and extended the middle part above the tow bar. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 30 guests |
