|
| falcon1999 |
|
|||
|
What spark plugs do you use for a Duel Fuel Falcon AU?
And what gap do you use?
_________________ What do you call a Hyundai with dual exhausts? |
|||
| Top | |
|||
| millview41 |
|
||
|
falcon1999 wrote: What spark plugs do you use for a Duel Fuel Falcon AU? And what gap do you use? Just use standard plugs without regards to LPG . This is what my Wife's car uses and runs fine . |
||
| Top | |
||
| ausedwagon |
|
|||
|
ZGR6B11
sue them there a little hotter (out of xr6) and work well for me
_________________ 94 White ED Wagon |
|||
| Top | |
|||
| TROYMAN |
|
||
|
ausedwagon wrote: ZGR6B11 sue them there a little hotter (out of xr6) and work well for me those plugs from xr6 are actually i range colder than std... |
||
| Top | |
||
| millview41 |
|
||
|
millview41 wrote: falcon1999 wrote: What spark plugs do you use for a Duel Fuel Falcon AU? And what gap do you use? Just use standard plugs without regards to LPG . This is what my Wife's car uses and runs fine . Standard plugs as was mentioned but gap no larger than 0.25/or metric 1.0 |
||
| Top | |
||
| ToranaGuy |
|
|||
|
ausedwagon wrote: ZGR6B11 I have used those plugs, tried with 1.0 & 0.8 gaps, run ok for me. I've currently got some non resistor plugs in, can't remember what they are, with a 0.9 gap & they are a bit better again, except for the ignition wine i can hear at low volumes in my stereo. I was thinking about changing back to the ZGR's and trying a 0.7gap & see what happens, if it's too close or if it works good. I've got a good coil, cap & rotor, near new dizzy & IC & E race series leads. I run LPG 90% of the time. Cheers ToranaGuy
_________________ I am the ToranaGuy!|74 Lh Torana Turbo|78 Hz PanelVan|86 Mighty Boy Ute|93 EB2 Ghia,GT Mockup,5spd,LPGI,Full Leather|2 x EB Xr8 5spd's|FS [VIC]: Wrecking - Eb XR8 - Parts available |Build Thread|Ebay Items - Ford Parts| |
|||
| Top | |
|||
| kassan1973 |
|
||
|
Use a bp6ey-11NGK dont use zgr as they are still a resister type plug which require a heap more spark to fire correctly
|
||
| Top | |
||
| ef_gas |
|
||
|
I use Autolite Xp63 and NGK perfomance Ignition Leads
|
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
AU1 needs a 0.9 gap.
AU2/3 can use a 1.1 gap. |
||
| Top | |
||
| xcabbi |
|
||
|
I just run xr6 plugs and gap them down to 0.8. Haven't had a back fire in over half a mill kms.
|
||
| Top | |
||
| AU99 |
|
|||
|
xcabbi wrote: I just run xr6 plugs and gap them down to 0.8. Haven't had a back fire in over half a mill kms. Thats what I ran in my AU S1 Duel Fuel... No probs in the 2 years I had it. Never backfired.
_________________ 2003 BA Falcon Egas Taxi Pack - XR Replica |
|||
| Top | |
|||
| ToranaGuy |
|
|||
|
I ended up playing with my gaps a bit, and found a 0.8mm gap on the ZGR6B11 plugs does really well for my setup. I tried std plugs gaped up & 0.8 & they don't run as good as the ZGR's.
You need to be careful about running non resistor plugs in car's with electronic ignition these days. Cheers ToranaGuy
_________________ I am the ToranaGuy!|74 Lh Torana Turbo|78 Hz PanelVan|86 Mighty Boy Ute|93 EB2 Ghia,GT Mockup,5spd,LPGI,Full Leather|2 x EB Xr8 5spd's|FS [VIC]: Wrecking - Eb XR8 - Parts available |Build Thread|Ebay Items - Ford Parts| |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 5 guests |
